Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
avr_bootloader:paper-avrisp_mk2 [2017/01/06 22:57] admin |
avr_bootloader:paper-avrisp_mk2 [2020/06/11 22:13] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== Paper-AVRISP mkII ==== | ===== Paper-AVRISP mkII ==== | ||
| - | Am AVRISP mkII clone made with Paper-PCBs. The controller is the ProMicro with the Atmel32U4 chip. The design is based on the | + | |
| + | An AVRISP mkII clone made out of Paper-PCBs.\\ | ||
| + | {{:avr_bootloader:paper-avrisp_mkii.jpg|}}\\ | ||
| + | The controller is a cheap ProMicro with the Atmel32U4 chip. The design is based on the | ||
| [[http://make.kosakalab.com/make/electronic-work/avrisp-mk2/leo-r3_avrisp-mk2_en/| | [[http://make.kosakalab.com/make/electronic-work/avrisp-mk2/leo-r3_avrisp-mk2_en/| | ||
| - | Kosakalab - Make the AVRISP mkII Clone from Arduino Leonardo / Micro]].\\ | + | Make the AVRISP mkII Clone from Arduino Leonardo / Micro]] by Kimio Kosaka.\\ |
| + | |||
| + | Front:\\ | ||
| + | {{:avr_bootloader:paper-avrisp_mkii_front.jpg?400|}}\\ | ||
| + | Back:\\ | ||
| + | {{:avr_bootloader:paper-avrisp_mkii_back.jpg?400|}}\\ | ||
| ---- | ---- | ||
| Line 18: | Line 26: | ||
| **Pin Out:**\\ | **Pin Out:**\\ | ||
| {{:avr_bootloader:promicro_pinout.jpg?400|}}\\ | {{:avr_bootloader:promicro_pinout.jpg?400|}}\\ | ||
| + | |||
| + | ---- | ||
| + | ==== Paper-PCB ==== | ||
| + | {{:avr_bootloader:paper-avrisp_mkii_02.jpg?400|}}\\ | ||
| + | {{ :avr_bootloader:paper-avrisp_mkii_02.zip |}}\\ | ||
| + | |||
| + | ---- | ||
| + | ==== Software ==== | ||
| + | Connect an AVR programmer to the Pro Micro: +5V, GND, Reset, MISO, MOSI, SCLK.\\ | ||
| + | ! It should be the Reset pin on the Pro Micro board not the one of the connector !\\ | ||
| + | |||
| + | With the Avrdude erase the Arduino Pro Micro:\\ | ||
| + | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -e | ||
| + | |||
| + | Set the fuses like that: lowFuse 0xFF, highFuse 0xD9, extendedFuse 0xC3:\\ | ||
| + | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -U lfuse:w:0xFF:m | ||
| + | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -U hfuse:w:0xD9:m | ||
| + | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -U efuse:w:0xC3:m | ||
| + | |||
| + | Burn the ATMega32U4-usbdevice_dfu-1_0_0.hex file on the Pro Micro. The file is included in the megaUSB_DFU_Bootloaders_2 folder:\\ | ||
| + | [[http://make.kosakalab.com/archives/megaUSB_DFU_Bootloaders_2.zip]]\\ | ||
| + | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -U flash:w:ATMega32U4-usbdevice_dfu-1_0_0.hex:i | ||
| + | |||
| + | Set Lock-Bits 0xEF:\\ | ||
| + | $ sudo avrdude -p m32u4 -c stk500v2 -P /dev/ttyACM0 -U lock:w:0xEF:m | ||
| + | |||
| + | Run the [[http://www.atmel.com/tools/FLIP.aspx|Atmel Flip-Tools]] like it's described at [[http://make.kosakalab.com/make/electronic-work/avrisp-mk2/leo-r3_avrisp-mk2_en//|Kimio Kosakas page]].\\ | ||
| + | Upload that file:[[http://make.kosakalab.com/archives/AVRISP-MKII_ATmega32u4.zip]].\\ | ||
| + | |||
| + | That's it! | ||
| + | |||
| + | Test it with an Atmega 328p:\\ | ||
| + | $ sudo avrdude -p m328p -c avrispmkII -P usb -U flash:w:optiboot_atmega328.hex:i | ||
| ---- | ---- | ||
| Line 35: | Line 76: | ||
| [[http://www.atmel.com/webdoc/atmelice/atmelice.using_ocd_physical_tpi.html|Atmel TPI Interfaces]]\\ | [[http://www.atmel.com/webdoc/atmelice/atmelice.using_ocd_physical_tpi.html|Atmel TPI Interfaces]]\\ | ||
| [[http://www.atmel.com/webdoc/atmelice/atmelice.using_ocd_physical_spi.html|Atmel SPI Interface]]\\ | [[http://www.atmel.com/webdoc/atmelice/atmelice.using_ocd_physical_spi.html|Atmel SPI Interface]]\\ | ||
| + | |||
| + | === Avrdude manual === | ||
| + | [[http://www.nongnu.org/avrdude/user-manual/avrdude_4.html]]\\ | ||
| + | |||
| + | {{:avr_bootloader:paper-avrisp_mkii.jpg?300|}}\\ | ||
| + | ---- | ||
| + | ==== License ==== | ||
| + | |||
| + | The Paper-AVRISP mkII was designed by **Wolfgang Spahn** 2017.\\ | ||
| + | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
| + | |||
| + | <html> | ||
| + | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
| + | </html> | ||
| ---- | ---- | ||