Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
raspberry_boards:duino-pi_modification [2016/01/20 21:51] admin [Install Shutdown & Reset Button] |
raspberry_boards:duino-pi_modification [2020/06/11 22:13] (current) |
||
|---|---|---|---|
| Line 7: | Line 7: | ||
| ---- | ---- | ||
| - | ==== Change the user and the password ==== | ||
| - | |||
| - | [[http://raspi.tv/2012/how-to-create-a-new-user-on-raspberry-pi|How to create a new user]] | ||
| - | |||
| - | 1. Change the name: | ||
| - | $ sudo nano /etc/hostname | ||
| - | in "duino-pi"\\ | ||
| - | |||
| - | 2. Change the host file | ||
| - | $ sudo nano /etc/hosts | ||
| - | in: | ||
| - | 127.0.0.1 localhost | ||
| - | ::1 localhost ip6-localhost ip6-loopback | ||
| - | fe00::0 ip6-localnet | ||
| - | ff00::0 ip6-mcastprefix | ||
| - | ff02::1 ip6-allnodes | ||
| - | ff02::2 ip6-allrouters | ||
| - | | ||
| - | 127.0.1.1 duino-pi | ||
| - | |||
| - | 5. Change the password | ||
| - | $ passwd | ||
| - | |||
| - | The passwd command allows you to change your password, you will be prompted for your old password, then you new password twice. The password is "dernulleffekt". | ||
| - | |||
| - | 4. Reboot: | ||
| - | $ sudo reboot | ||
| - | |||
| - | ---- | ||
| ==== Install Shutdown & Reset Button ==== | ==== Install Shutdown & Reset Button ==== | ||
| Line 43: | Line 14: | ||
| 2. Download and unzip that Python script | 2. Download and unzip that Python script | ||
| - | <del>$ wget http://www.dernulleffekt.de/programme/shutdownbutton.py.tar.gz</del> | ||
| $ wget http://www.dernulleffekt.de/programme/shutdownbutton_02.py.tar | $ wget http://www.dernulleffekt.de/programme/shutdownbutton_02.py.tar | ||
| - | $ tar xf shutdownbutton.py.tar.gz | + | $ tar xf shutdownbutton_02.py.tar |
| | | ||
| 2. Change owner & rights | 2. Change owner & rights | ||
| Line 82: | Line 52: | ||
| $ sudo nano /etc/rc.local | $ sudo nano /etc/rc.local | ||
| write before exit 0: | write before exit 0: | ||
| - | # run reset and shutdown script | + | # blink an LED |
| printf "Starting blinking LED on GPIO 22" | printf "Starting blinking LED on GPIO 22" | ||
| /home/pi/paper-duino-pi/blink_22.py & | /home/pi/paper-duino-pi/blink_22.py & | ||
| Line 167: | Line 137: | ||
| ---- | ---- | ||
| - | ==== Set the SSH connection ==== | ||
| - | |||
| - | 1. For activating the SSH connection open | ||
| - | $ sudo raspi-config | ||
| - | In 8. Advanced Options you can activate SSH | ||
| - | |||
| - | 2. Give the Raspberry Pi an IP address. Open the interfaces file: | ||
| - | $ sudo nano /etc/network/interfaces | ||
| - | Change the DHCP in static and add these lines: | ||
| - | |||
| - | iface eth0 inet static | ||
| - | address 192.168.0.111 | ||
| - | netmask 255.255.255.0 | ||
| - | gateway 192.168.0.100 | ||
| - | |||
| - | To save and leave press:\\ | ||
| - | CTRL+O, Enter, CTRL+X | ||
| - | |||
| - | 3. Restart ethernet | ||
| - | $ sudo ifdown eth0 | ||
| - | $ sudo ifup eth0 | ||
| - | |||
| - | 3. Now you can login on your computer with: | ||
| - | $ ssh duino-pi@192.168.0.111 | ||
| - | or with XWindows support: | ||
| - | $ ssh -XY pi@192.168.0.111 | ||
| - | PW: raspberry\\ | ||
| - | |||
| - | ---- | ||
| - | |||