Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
paper_bits:pb202_miditocv [2016/10/24 03:28] admin [PB202 MIDI to CV] |
paper_bits:pb202_miditocv [2020/06/11 22:13] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | =====PB202 MIDI to CV ===== | + | ===== PB202 MIDI to CV ===== |
+ | |||
+ | That MIDI and MIDI over USB board give four 0 to 5V output signals, CV1, CH2, CV3 and CV4. CV1 and CV2 are filtered.\\ | ||
+ | The CCNumber are 1, 2, 3 and 4 on chanel 1. That can be easily modified in the code.\\ | ||
+ | The board also outputs a trigger signal on an clock impulse. The poti is used as a clock divider.\\ | ||
- | That MIDI and MIDI over USB board give two 0 to 5V output signals, CV1 and CV2.\\ | ||
- | The CCNumber are 1 and 2 on chanel 1. That can be easily modified in the code.\\ | ||
{{:paper_bits:pb202_midi_to_cv_015617.jpg|}}\\ | {{:paper_bits:pb202_midi_to_cv_015617.jpg|}}\\ | ||
+ | |||
+ | For uploading code on the Arduino the Midi In jumper has to be off. One has to set the jumper for getting Midi in on the Arduino.\\ | ||
+ | |||
---- | ---- | ||
==== Paper-PCB ==== | ==== Paper-PCB ==== | ||
- | {{:paper_bits:pb202_midi_to_vc_02.jpg?300|}}\\ | + | {{:paper_bits:pb202_midi_to_vc_22.jpg?400|}}\\ |
- | {{ :paper_bits:pb202_midi_to_vc_02.ai.zip |}} | + | {{ :paper_bits:pb202_midi_to_vc_22.zip |}}\\ |
---- | ---- | ||
==== Software ==== | ==== Software ==== | ||
- | {{ :paper_bits:paperbits_miditocv_02.zip |}}\\ | + | {{ :paper_bits:paperbits_miditocv_23.zip |}}\\ |
---- | ---- | ||
- | ~~socialite:icon facebook twitter googleplus reddit tumblr~~ | + | ==== Parts ==== |
+ | * **Resistors:** | ||
+ | * 1x 220 Ohm | ||
+ | * 5x 470 Ohm | ||
+ | * 1x 1 kOhm | ||
+ | * 1x 3.3 kOhm | ||
+ | * 4x 27 KOhm | ||
+ | * **Capacitors:** | ||
+ | * 4x 1 nF | ||
+ | * 4x 470 nF | ||
+ | * **Semiconductors**: | ||
+ | * Arduino Pro Micro (Atmega 32U4) | ||
+ | * OpAmp MCP6002 | ||
+ | * Optocoupler 6N138 | ||
+ | * **Diodes** | ||
+ | * 1x 1N4148 | ||
+ | * **Potentiometer:** | ||
+ | * 1x 100 kOhm | ||
+ | * **Mechanical:** | ||
+ | * 1x IC socket, 28 pin | ||
+ | * 2x IC socket, 8 pin | ||
+ | * 1x pin strip 1x10 pin | ||
+ | * 2x pin header, female 12 pin | ||
+ | * 2x pin header, female 90° 1x3, 1x2 | ||
+ | * 2x pin header, male 90° 1x3, 1x2 | ||
+ | * 2x push button | ||
+ | * 3x jumpers | ||
---- | ---- | ||
- | ~~DISCUSSION~~ | + | ==== License ==== |
+ | The PB202 MIDI to CV was designed by **Wolfgang Spahn**, 2017-20.\\ | ||
+ | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
+ | <html> | ||
+ | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
+ | </html> | ||
+ | |||
+ | ---- |