Differences
This shows you the differences between two versions of the page.
avr_bootloader:paper-avrisp_mk2 [2017/01/08 00:16] admin |
avr_bootloader:paper-avrisp_mk2 [2020/06/11 22:13] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== Paper-AVRISP mkII ==== | ||
- | Am AVRISP mkII clone made with Paper-PCBs. The controller is the ProMicro with the Atmel32U4 chip. The design is based on the | ||
- | [[http://make.kosakalab.com/make/electronic-work/avrisp-mk2/leo-r3_avrisp-mk2_en/| | ||
- | Kosakalab - Make the AVRISP mkII Clone from Arduino Leonardo / Micro]].\\ | ||
- | |||
- | ---- | ||
- | ==== Pro Micro Modification ==== | ||
- | |||
- | ** TX Line Connection:**\\ | ||
- | Solder a wire between the resistor of the TX LED and A0.\\ | ||
- | {{:avr_bootloader:promicro_txledconnection.jpg?400|}}\\ | ||
- | |||
- | ** Close the Jumper: **\\ | ||
- | The Chinese Pro Micro clones have a 5V converter on board. That means when powered over USB the Pro Micro runs on 4.7V. To close the jumper will avoid that (it´s next to the USB socket). But never power the Pro Micro over the RAW input again! Check the | ||
- | [[http://cdn.sparkfun.com/datasheets/Dev/Arduino/Boards/SparkFun_Pro_Micro_v13a.pdf|original sparkfun schematic]] for details.\\ | ||
- | In putting a little bit of solder on J1 of the Pro Micro Clone you close the jumper and bypass the voltage converter of the board. | ||
- | |||
- | **Pin Out:**\\ | ||
- | {{:avr_bootloader:promicro_pinout.jpg?400|}}\\ | ||
- | |||
- | ---- | ||
- | ==== Paper-PCB ==== | ||
- | {{:avr_bootloader:paper-avrisp_mkii_02.jpg?400|}}\\ | ||
- | {{ :avr_bootloader:paper-avrisp_mkii_02.zip |}}\\ | ||
- | |||
- | ---- | ||
- | ==== Knowledge ==== | ||
- | |||
- | === The Arduino Pro Micro === | ||
- | [[https://www.sparkfun.com/products/12640]]\\ | ||
- | <html> | ||
- | <div align="left"> | ||
- | <a href="https://cdn.sparkfun.com/assets/9/c/3/c/4/523a1765757b7f5c6e8b4567.png"> | ||
- | <img src="https://cdn.sparkfun.com/assets/9/c/3/c/4/523a1765757b7f5c6e8b4567.png" width=200 alt=""></a> | ||
- | </div> | ||
- | </html> | ||
- | |||
- | === Connector === | ||
- | {{:avr_bootloader:usb_avr_mkii_connectors.png?400|}}\\ | ||
- | [[http://www.atmel.com/webdoc/atmelice/atmelice.using_ocd_physical_tpi.html|Atmel TPI Interfaces]]\\ | ||
- | [[http://www.atmel.com/webdoc/atmelice/atmelice.using_ocd_physical_spi.html|Atmel SPI Interface]]\\ | ||
- | |||
- | ---- | ||
- | ~~socialite:icon facebook twitter googleplus reddit tumblr~~ | ||
- | |||
- | ---- | ||
- | ~~DISCUSSION~~ | ||