Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
arduino_clones:papercocomake7 [2018/05/25 18:27] admin |
arduino_clones:papercocomake7 [2020/06/11 22:13] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== PaperCocoMake7 ===== | + | ===== Paper CocoMake7 ===== |
The PaperCocoMake7 in an Arduino board based on Paper PCB and an ATtiny85 chip. It is the paper version of the [[https://cocomake7.github.io/#|CocoMake7]]. | The PaperCocoMake7 in an Arduino board based on Paper PCB and an ATtiny85 chip. It is the paper version of the [[https://cocomake7.github.io/#|CocoMake7]]. | ||
Line 6: | Line 6: | ||
Here you find an other ATiny board the [[arduino_clones:papertiny|PaperTiny]].\\ | Here you find an other ATiny board the [[arduino_clones:papertiny|PaperTiny]].\\ | ||
- | {{:arduino_clones:papercocomake7.jpg|}}\\ | + | **Paper CocoMake7**\\ |
+ | {{:arduino_clones:papercocomake7.jpg?400|}}\\ | ||
+ | |||
+ | **Paper CocoMake**\\ | ||
+ | {{:arduino_clones:papercocomake1.jpg?400|}}\\ | ||
---- | ---- | ||
==== Paper PCB ==== | ==== Paper PCB ==== | ||
- | **with audio out and no power on board:**\\ | + | |
+ | **Paper CocoMake7** with audio out and no power on board:\\ | ||
{{:arduino_clones:papercocomake7_03.jpg?200|}}\\ | {{:arduino_clones:papercocomake7_03.jpg?200|}}\\ | ||
- | {{ :arduino_clones:papercocomake7_03.zip |}} | + | {{ :arduino_clones:papercocomake7_03.zip |}}\\ |
- | **without audio out and power on board:**\\ | + | |
+ | **Paper CocoMake** with power on board no audio out:\\ | ||
{{:arduino_clones:papercocomake1_10.jpg?200|}}\\ | {{:arduino_clones:papercocomake1_10.jpg?200|}}\\ | ||
{{ :arduino_clones:papercocomake1_10.zip |}}\\ | {{ :arduino_clones:papercocomake1_10.zip |}}\\ | ||
Line 18: | Line 24: | ||
---- | ---- | ||
==== Schematic ==== | ==== Schematic ==== | ||
- | It's the one from [[https://cocomake7.github.io/#]], I just used 2k resistors for the LED resistors and added a power supply.\\ | + | It's the same schematic as the one from [[https://cocomake7.github.io/#]], I just used 2k as the LED resistors and added a power supply.\\ |
{{:arduino_clones:mrbaladuinoone_schematic.png?400|}}\\ | {{:arduino_clones:mrbaladuinoone_schematic.png?400|}}\\ | ||
Line 26: | Line 32: | ||
* 2x 2 kOhm | * 2x 2 kOhm | ||
* 1x 1.5 kOhm | * 1x 1.5 kOhm | ||
- | * 1x 47 kOhm | + | * 1x 47 kOhm(1) |
* 2x 68 Ohm | * 2x 68 Ohm | ||
* **Capacitors:** | * **Capacitors:** | ||
* 2x 100 nF | * 2x 100 nF | ||
+ | * 1x 10µF(1) | ||
+ | * 1x 100µF(2) | ||
* **Diodes:** | * **Diodes:** | ||
* 2x Z-Diode 3,3V | * 2x Z-Diode 3,3V | ||
* **Semiconductors** | * **Semiconductors** | ||
* 2x Standart LED | * 2x Standart LED | ||
- | * 1x 7805 | + | * 1x 7805(2) |
* **Mechanical:** | * **Mechanical:** | ||
* 1x IC socket, 8pins | * 1x IC socket, 8pins | ||
- | * 1x Pin-Strip male 1x2 | + | * 1x Pin-Strip male 1x2(2) |
* 2x Pin-Strip female 1x4 | * 2x Pin-Strip female 1x4 | ||
- | * jack socket | + | * jack socket(1) |
+ | (1) Paper CocoMake7\\ | ||
+ | (2) Paper CocoMake\\ | ||
---- | ---- | ||
+ | ==== License ==== | ||
+ | |||
+ | The Paper CocoMake7 was designed by **Wolfgang Spahn** 2017-18.\\ | ||
+ | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
- | ~~socialite:icon facebook twitter googleplus reddit tumblr~~ | + | <html> |
+ | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
+ | </html> | ||
---- | ---- |