Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
raspberry_boards:paperduinopi_hat [2016/07/16 22:43] admin |
raspberry_boards:paperduinopi_hat [2020/06/11 22:13] (current) |
||
---|---|---|---|
Line 44: | Line 44: | ||
$ mkdir paper-duino-pi | $ mkdir paper-duino-pi | ||
$ cd paper-duino-pi | $ cd paper-duino-pi | ||
- | Download and unpack the files: | + | Download the files: |
$ wget http://dernulleffekt.de/programme/paperduinopi_v05/paper-duino-hat_01.tar.gz | $ wget http://dernulleffekt.de/programme/paperduinopi_v05/paper-duino-hat_01.tar.gz | ||
- | $ tar -xvf paper-duino-pi_Pi2_Jessy.tar.gz | + | And unpack: |
+ | $ tar -xvf paper-duino-hat_01.tar.gz | ||
Run the setup: | Run the setup: | ||
$ sudo chmod 755 setup | $ sudo chmod 755 setup | ||
Line 75: | Line 76: | ||
$ sudo nano /etc/rc.local | $ sudo nano /etc/rc.local | ||
Write before "exit 0": | Write before "exit 0": | ||
- | # run reset and shutdown script | + | printf ">>>>>>>> PAPER-DUINO-HAT 07_2016 http://dernulleffekt.de\n" |
- | printf "Starts shutdown aund reset button on GPIO 22\n" | + | |
- | /home/pi/paper-duino-pi/shutdownbutton_hat.py & | + | # run reset and shutdown script |
- | # blink an LED | + | printf ">>>>>>>> Starting shutdown aund reset button on GPIO 22\n" |
- | printf "Starts blinking LED on GPIO 27\n" | + | /home/pi/paper-duino-pi/shutdownbutton_hat.py & |
- | /home/pi/paper-duino-pi/blink_hat.py & | + | |
+ | # blink an LED | ||
+ | printf ">>>>>>>> Starting blinking LED on GPIO 27\n" | ||
+ | /home/pi/paper-duino-pi/blink_hat.py & | ||
To save and leave press: CTRL+O, Enter, CTRL+X\\ | To save and leave press: CTRL+O, Enter, CTRL+X\\ | ||
Reboot: | Reboot: | ||
Line 90: | Line 95: | ||
{{:raspberry_boards:spi-connection_202802.jpg?400|}}\\ | {{:raspberry_boards:spi-connection_202802.jpg?400|}}\\ | ||
- | Raspberry Pi | Arduino | + | Raspberry Pi | Paper-Duino-Hat |
====================================== | ====================================== | ||
MOSI (GPIO 10) | MOSI (pin 11) | MOSI (GPIO 10) | MOSI (pin 11) | ||
Line 97: | Line 102: | ||
RST (GPIO 25) | Reset | RST (GPIO 25) | Reset | ||
GND | GND | GND | GND | ||
- | 3.3V | 3,3V | + | 3.3V | 5V |
Run on the following commands:\\ | Run on the following commands:\\ | ||
Line 113: | Line 118: | ||
---- | ---- | ||
- | ~~socialite:icon facebook twitter googleplus reddit~~ | + | ==== License ==== |
+ | |||
+ | The Paper-Duino-Hat was designed by **Wolfgang Spahn** 2012-16.\\ | ||
+ | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
+ | |||
+ | <html> | ||
+ | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
+ | </html> | ||
---- | ---- | ||
+ |