Differences
This shows you the differences between two versions of the page.
|
raspberry_boards:duino-pi_modification [2016/01/20 21:41] admin |
raspberry_boards:duino-pi_modification [2020/06/11 22:13] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ===== Paper-Duino-Pi software modifications ===== | ||
| - | |||
| - | Before start make an update: | ||
| - | $ sudo apt-get update | ||
| - | $ sudo apt-get upgrade | ||
| - | |||
| - | ---- | ||
| - | |||
| - | ==== Change the user and the password ==== | ||
| - | |||
| - | [[http://raspi.tv/2012/how-to-create-a-new-user-on-raspberry-pi|How to create a new user]] | ||
| - | |||
| - | 1. Change the name: | ||
| - | $ sudo nano /etc/hostname | ||
| - | in "duino-pi"\\ | ||
| - | |||
| - | 2. Change the host file | ||
| - | $ sudo nano /etc/hosts | ||
| - | in: | ||
| - | 127.0.0.1 localhost | ||
| - | ::1 localhost ip6-localhost ip6-loopback | ||
| - | fe00::0 ip6-localnet | ||
| - | ff00::0 ip6-mcastprefix | ||
| - | ff02::1 ip6-allnodes | ||
| - | ff02::2 ip6-allrouters | ||
| - | | ||
| - | 127.0.1.1 duino-pi | ||
| - | |||
| - | 5. Change the password | ||
| - | $ passwd | ||
| - | |||
| - | The passwd command allows you to change your password, you will be prompted for your old password, then you new password twice. The password is "dernulleffekt". | ||
| - | |||
| - | 4. Reboot: | ||
| - | $ sudo reboot | ||
| - | |||
| - | ---- | ||
| - | ==== Install Shutdown & Reset Button ==== | ||
| - | |||
| - | 1. Make an folder | ||
| - | $ mkdir /home/pi/paper-duino-pi | ||
| - | $ cd /home/pi/paper-duino-pi | ||
| - | |||
| - | 2. Download and unzip that Python script | ||
| - | $ wget http://www.dernulleffekt.de/programme/shutdownbutton.py.tar.gz | ||
| - | $ tar xf shutdownbutton.py.tar.gz | ||
| - | | ||
| - | 2. Change owner & rights | ||
| - | $ sudo chown root:root shutdownbutton.py | ||
| - | $ sudo chmod 755 shutdownbutton.py | ||
| - | | ||
| - | 3. Create the autostart: | ||
| - | $ sudo nano /etc/rc.local | ||
| - | write before exit 0: | ||
| - | # run reset and shutdown script | ||
| - | printf "Starting shutdown aund reset button\n" | ||
| - | /home/pi/paper-duino-pi/shutdownbutton.py & | ||
| - | |||
| - | To save and leave press:\\ | ||
| - | CTRL+O, Enter, CTRL+X\\ | ||
| - | |||
| - | 4. Reboot | ||
| - | $ sudo reboot | ||
| - | \\ | ||
| - | |||
| - | ---- | ||
| - | ==== Install the Arduino IDE & modify ==== | ||
| - | |||
| - | 1. Install the Arduino IDE, type in command line: | ||
| - | $ sudo apt-get installl arduino | ||
| - | |||
| - | 2. For the modification of the GPIO Pin and the Avrdude, the easiest way is to download the setup for the AlaMode board: | ||
| - | $ wget http://www.wyolum.com/downloads/alamode-setup.tar.gz | ||
| - | unpack it | ||
| - | $ sudo tar xf alamode-setup.tar.gz | ||
| - | and run the setup. | ||
| - | $ cd alamode-setup | ||
| - | $ sudo ./setup | ||
| - | That will install a new version of the avrdude and will also do some Linux modifications (one for the alamode board). | ||
| - | |||
| - | 3. To modifier the Arduino IDE setup for the Paper-Duino-Pi you have to type in the terminal: | ||
| - | $ sudo nano /usr/share/arduino/hardware/arduino/boards.txt | ||
| - | Change the name of the board: | ||
| - | alamode.name=Paper-Duino-Pi | ||
| - | The baud rate should be set to 57600: | ||
| - | alamode.upload.speed=57600 | ||
| - | Than change the fuses from 0xde to: | ||
| - | alamode.bootloader.high_fuses=0xda | ||
| - | and save it!\\ | ||
| - | |||
| - | 4. Reboot | ||
| - | $ sudo reboot | ||
| - | |||
| - | After resetting the Raspberry Pi a new serial port: dev/ttyS0 and a new board: Paper-Duino-Pi will appear in your Arduino IDE. For uploading a program use the Paper-Duio-Pi board and the ttyS0 port.\\ | ||
| - | |||
| - | Thanks for the avrdude modification to: | ||
| - | [[http://wyolum.com/projects/alamode/|Wyolum.com]]\\ | ||
| - | |||
| - | Here are some details of the [[raspberry_boards:serial_modification|serial modification]]\\ | ||
| - | \\ | ||
| - | |||
| - | ---- | ||
| - | ==== Install Pure Data, PD-extended ==== | ||
| - | |||
| - | 1. To install pd-extended run the following command in your terminal: | ||
| - | $ sudo nano /etc/apt/sources.list | ||
| - | copy/paste this line to the list(right-click to paste): | ||
| - | deb-src http://archive.raspbian.org/raspbian wheezy main contrib non-free rpi | ||
| - | To save and leave:\\ | ||
| - | CTRL+O, Enter, CTRL+X | ||
| - | |||
| - | 2. Update | ||
| - | $ sudo apt-get update | ||
| - | |||
| - | 3. Download pd-extended | ||
| - | $ wget https://puredata.info/downloads/pd-extended-0-43-3-on-raspberry-pi-raspbian-wheezy-armhf/releases/1.0/Pd-0.43.3-extended-20121004.deb | ||
| - | |||
| - | 4. Install the package | ||
| - | $ sudo dpkg -i Pd-0.43.3-extended-20121004.deb | ||
| - | |||
| - | 5. Fix the installation | ||
| - | $ sudo apt-get -f install | ||
| - | it should be installed. | ||
| - | |||
| - | 6. Change the root priorities: | ||
| - | $ sudo chmod 4755 /usr/bin/pd-extended | ||
| - | \\ | ||
| - | |||
| - | ---- | ||
| - | ==== Download the Firmata ==== | ||
| - | |||
| - | 1. Create folder | ||
| - | $ mkdir /home/pi/pd-sketchbook | ||
| - | $ cd /home/pi/pd-sketchbook | ||
| - | 2. Download and unpack | ||
| - | $ wget http://at.or.at/hans/pd/Pduino-0.5.zip | ||
| - | $ unzip Pduino-0.5.zip | ||
| - | \\ | ||
| - | |||
| - | ---- | ||
| - | ==== Set the SSH connection ==== | ||
| - | |||
| - | 1. For activating the SSH connection open | ||
| - | $ sudo raspi-config | ||
| - | In 8. Advanced Options you can activate SSH | ||
| - | |||
| - | 2. Give the Raspberry Pi an IP address. Open the interfaces file: | ||
| - | $ sudo nano /etc/network/interfaces | ||
| - | Change the DHCP in static and add these lines: | ||
| - | |||
| - | iface eth0 inet static | ||
| - | address 192.168.0.111 | ||
| - | netmask 255.255.255.0 | ||
| - | gateway 192.168.0.100 | ||
| - | |||
| - | To save and leave press:\\ | ||
| - | CTRL+O, Enter, CTRL+X | ||
| - | |||
| - | 3. Restart ethernet | ||
| - | $ sudo ifdown eth0 | ||
| - | $ sudo ifup eth0 | ||
| - | |||
| - | 3. Now you can login on your computer with: | ||
| - | $ ssh duino-pi@192.168.0.111 | ||
| - | or with XWindows support: | ||
| - | $ ssh -XY pi@192.168.0.111 | ||
| - | PW: raspberry\\ | ||
| - | |||
| - | ---- | ||
| - | |||