Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
paper_synth:ps411_envamp [2017/04/18 18:38] admin |
paper_synth:ps411_envamp [2020/06/11 22:13] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | =====PS411 EnvAmp (Attack/Release Envelope Generator & Opto-VCA)===== | + | ===== PS411 EnvAmp (Attack/Release Envelope Generator & Opto-VCA)===== |
+ | by Antti Pussinen\\ | ||
The Dynamics of synthesized sounds are controlled with a Voltage Controlled Amplifier, or VCA. | The Dynamics of synthesized sounds are controlled with a Voltage Controlled Amplifier, or VCA. | ||
Line 7: | Line 8: | ||
Vactrol based Opto-VCA add an Attack and Release time automatically due to the relatively slow turn on, and off times of the led-ldr pair inside a vactrol. The ”opto” part of our VCA is a fast and accurate AC-Optocoupler, which adds a tiny bit of Attack time and Release tail to the signal, but not so much as a Vactrol would. We Decided to go with the optocoupler since factory made Vactrols are getting more rare and expensive, and altho rolling your own is a good choice, the response varies due to led and ldr types and manufacture tolerances. | Vactrol based Opto-VCA add an Attack and Release time automatically due to the relatively slow turn on, and off times of the led-ldr pair inside a vactrol. The ”opto” part of our VCA is a fast and accurate AC-Optocoupler, which adds a tiny bit of Attack time and Release tail to the signal, but not so much as a Vactrol would. We Decided to go with the optocoupler since factory made Vactrols are getting more rare and expensive, and altho rolling your own is a good choice, the response varies due to led and ldr types and manufacture tolerances. | ||
+ | |||
+ | <html> | ||
+ | <iframe width="600" height="338" src="https://www.youtube.com/embed/pwurOpNAjtI?rel=0&showinfo=0" frameborder="0" allowfullscreen></iframe> | ||
+ | </html> | ||
The Paper Synthesizer PS411 adds more control to the opto-VCA with Attack and Release control potentiometers. If both turned to zero, the module acts like a normal VCA, controlled by external CV. | The Paper Synthesizer PS411 adds more control to the opto-VCA with Attack and Release control potentiometers. If both turned to zero, the module acts like a normal VCA, controlled by external CV. | ||
If Attack or Release are adjusted, it affects the input CV before it controls the VCA. If CV input is a Gate signal, the envelope generator works like a normal Attack Release generator. Created envelope can be used to also control other modules view envelope output connector. A led is used to visualize the envelope. A jumper in the board selects between long and short attack and release ranges. | If Attack or Release are adjusted, it affects the input CV before it controls the VCA. If CV input is a Gate signal, the envelope generator works like a normal Attack Release generator. Created envelope can be used to also control other modules view envelope output connector. A led is used to visualize the envelope. A jumper in the board selects between long and short attack and release ranges. | ||
- | |||
- | {{:paper_synth:ps411_scope_pic.jpg?600|}}\\ | ||
The module comes also with an bipolar offset potentiometer for manually controlling the amplitude. | The module comes also with an bipolar offset potentiometer for manually controlling the amplitude. | ||
- | {{:paper_synth:ps411_print_201126_1200.jpg?600|}}\\ | + | ---- |
+ | ====Scope==== | ||
+ | {{:paper_synth:ps411_scope_pic.jpg?400|}}\\ | ||
---- | ---- | ||
==== Schematic ==== | ==== Schematic ==== | ||
- | {{:paper_synth:ps411-origami_envamp_1200.jpg?600|}}\\ | + | {{:paper_synth:ps411-origami_envamp_1200.jpg?400|}}\\ |
---- | ---- | ||
+ | ==== Paper PCB ==== | ||
+ | {{:paper_synth:ps411_envamp_10.jpg?400|}}\\ | ||
+ | {{ :paper_synth:ps411_envamp_10.zip|}}\\ | ||
+ | |||
+ | ---- | ||
+ | ==== Faceplate ==== | ||
+ | {{:paper_synth:ps411_envamp_faceplate_11.jpg?200|}}\\ | ||
+ | |||
+ | ---- | ||
+ | ==== Parts ==== | ||
+ | * **Resistors:** | ||
+ | * 1x 68 Ohm | ||
+ | * 1x 100 Ohm | ||
+ | * 3x 1 kOhm | ||
+ | * 2x 10 kOhm | ||
+ | * 1x 1.5 kOhm | ||
+ | * 1x 5.6kOhm | ||
+ | * 5x 100 kOhm | ||
+ | * 2x 470kOhm | ||
+ | * **Capacitors:** | ||
+ | * 1x 22µF (bipolar) | ||
+ | * **Diodes:** | ||
+ | * 5x 1N4148 | ||
+ | * 1x LED | ||
+ | * **Semiconductors** | ||
+ | * 1x TL072 OpAmp | ||
+ | * 1x TL074 OpAmp | ||
+ | * 1x H11F1 Optocoupler | ||
+ | * **Mechanical:** | ||
+ | * 1x IC socket, 8pins | ||
+ | * 1x IC socket, 16pins | ||
+ | * 1x IC socket, 6pins | ||
+ | * 4x Thonkiconn 3.5mm jack socket | ||
+ | * 1x pin strip 2x8 | ||
+ | * **Trimmpotentiometer:** | ||
+ | * 1x 50 k | ||
+ | * **Potentiometers:** | ||
+ | * 2x 100k lin | ||
+ | * 1x 100k log | ||
+ | |||
+ | ---- | ||
+ | ==== License ==== | ||
+ | |||
+ | The PS411 EnvAmp was designed by **Antti Pussinen** 2017.\\ | ||
+ | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
+ | |||
+ | <html> | ||
+ | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
+ | </html> | ||
+ | |||
+ | ---- | ||
+ | |||
+ | |||
+ | |||
+ |