Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
paper_bits:pb204_sync-sequencer [2019/11/01 09:28] admin |
paper_bits:pb204_sync-sequencer [2020/03/20 22:01] admin [Manual] |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| ==== Manual ==== | ==== Manual ==== | ||
| - | **set the CV output:**\\ | + | === Assigning CV === |
| - | set MODE switch to CV.\\ | + | Set the MODE switch to CV.\\ |
| - | To change the output for each step one select a value with the BEAT/CV potentiometer and in pressing the button for the selected step the selected voltage will be assigned to that individual step.\\ | + | To change the output for each step one select a value with the BEAT/CV potentiometer and in pressing the button for a specific step the selected voltage will be assigned to that step.\\ |
| - | Depending on the CV switch selection it will be independently stored for the output 1 or 2.\\ | + | Depending on the selection of the CV switch it will be independently stored for the output 1 or 2.\\ |
| - | **set the rhythm**\\ | + | === Rhythm === |
| - | set MODE switch to BEAT.\\ | + | Set the MODE switch to BEAT. Now one can change the length of each step. One can select a value by rotating the BEAT/CV potentiometer and in pressing the button at a specific step the selected value will be assigned to that step.\\ |
| - | To change the length of each step one select a value with the BEAT/CV potentiometer and in pressing the button for the selected step the selection will be assigned to that individual step.\\ | + | It just will work if the Ex-Trigger switch is OFF.\\ |
| - | It just works if Ex-Trigger is OFF.\\ | + | |
| - | **set the steps:\\ | + | === Steps === |
| To change between 2 and 8 steps one can use the STEP potentiometer.\\ | To change between 2 and 8 steps one can use the STEP potentiometer.\\ | ||
| - | If one select 1 step the Sync Sequencer goes into the **1 STEP MODE**. With the SPEED potentiometer one can now select each individual step. That makes it easy to program the sequencer.\\ | + | If one select 1 step the Sync Sequencer goes into the **1 STEP MODE**. By rotating the SPEED potentiometer one can now move to each individual step. That makes it much easy to program the sequencer.\\ |
| - | **change the speed:\\ | + | === Change the Speed === |
| - | The speed can be set withe the SPEED potentiometer or with an external control voltage. For that the Ex-Speed switch has to be set on ON and with a jumper one can select between BUS 1 and BUS 2 as the CV source.\\ | + | The speed can be set withe the SPEED potentiometer or with an external control voltage. For the external control the Ex-Speed switch has to be on ON and with a jumper one can choose if the voltage source coming from BUS 1 or BUS 2.\\ |
| - | If the Sync Sequencer is in the **STEP 1 MODE** instead of the speed the control voltage will change the individual step.\\ | + | If the Sequencer is in the **STEP 1 MODE** one can change the active steps with the control voltage, too.\\ |
| - | **external trigger** | + | === External Trigger === |
| - | If one wants to use an external trigger signal one has to set the Ex-Trigger switch on ON and then use the Gate for the trigger input or instead of the TRIGGER jumper one can attache an jumper wire to the marked pin.\\ | + | If one wants to use an external trigger signal one has to set the Ex-Trigger switch on ON. If the TRIGGER jumper is set the trigger signal will come over the Gate BUS. If the jumper is not set then one can use the pin marked with IN for a trigger signal input.\\ |
| ---- | ---- | ||
| - | |||
| ==== Paper-PCB ==== | ==== Paper-PCB ==== | ||