Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
avr_bootloader:paper_usbasp [2013/03/22 23:42] admin |
avr_bootloader:paper_usbasp [2020/06/11 22:13] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | **== Paper USBasp ==========================================** | + | ===== Paper-USBasp ===== |
- | That board based on the [[http://www.fischl.de/usbasp/|USBasp Board]] of [[http://www.fischl.de|Thomas Fischl]]. There one find all schematics and manuals for the board.\\ | + | The Paper-USBasp is a Paper-PCB version of an USB in-circuit programmer for Atmel AVR controllers. The board based on the [[http://www.fischl.de/usbasp/|USBasp Board]] of [[http://www.fischl.de|Thomas Fischl]]. |
- | On the paper version the serial connection (RX and TX) were removed. A jumper for 3.6V was added.\\ | + | On the paper version the serial connection (RX and TX) were removed. A jumper for 3.6V was added. |
- | {{ :avr_bootloader:paper_usbasp_-_programmer_board_1265.jpg?460 |}} | + | The Paper USBasp can be perfectly combined with the [[avr_bootloader:programming_board|Programming Board]] for programming AVR chips: |
- | The Paper USBasp can be perfectly combined with the [[avr_bootloader:programming_board|Programming Board]]. | + | |
- | {{ :avr_bootloader:paper_usbasp_1274.jpg?300 |}}\\ | + | |
- | Or just be used to burn your bootloader on the [[arduino_clones:paperduino-uno|Paperduino-Uno]]. | + | |
- | {{:avr_bootloader:paper_usbasp_front_1266.jpg?200|}}\\ | + | {{ :avr_bootloader:paper_usbasp_-_programmer_board_1265.jpg?300 |}} |
- | {{:avr_bootloader:paper_usbasp_back_1267.jpg?200|}}\\ | + | |
+ | Or certainly it can be used to burn your bootloader on your [[arduino_clones:paperduino-uno|Paperduino-Uno]]: | ||
+ | {{ :avr_bootloader:paper_usbasp_1274.jpg?300 |}} | ||
+ | |||
+ | Here: [[http://www.fundf.net/usbasp/]] one find all schematics and manuals for the original USBasp board. They are similar to the paper version of the programmer. | ||
+ | |||
+ | Front: | ||
+ | |||
+ | {{:avr_bootloader:paper_usbasp_front_1266.jpg?200|}} | ||
+ | |||
+ | Back: | ||
+ | |||
+ | {{:avr_bootloader:paper_usbasp_back_1267.jpg?200|}} | ||
+ | |||
+ | Here is a manual for [[avr_bootloader:burning_firmware|burning the firmware]] | ||
+ | |||
+ | ---- | ||
+ | ==== Paper-PCB ==== | ||
- | **== Paper-PCB ============================================** | ||
{{:avr_bootloader:paper-usbasp_20_pub_stripes.jpg?200|}}\\ | {{:avr_bootloader:paper-usbasp_20_pub_stripes.jpg?200|}}\\ | ||
{{:avr_bootloader:paper-usbasp_20_pub.jpg?200|}}\\ | {{:avr_bootloader:paper-usbasp_20_pub.jpg?200|}}\\ | ||
{{:avr_bootloader:paper-usbasp_20_pub.xcf.zip|}}\\ | {{:avr_bootloader:paper-usbasp_20_pub.xcf.zip|}}\\ | ||
- | **== Components ===========================================** | + | ---- |
+ | ==== Parts ==== | ||
* Atmega8 or Atmega48 | * Atmega8 or Atmega48 | ||
* IC socket, 28 pin | * IC socket, 28 pin | ||
Line 34: | Line 46: | ||
* pins and jumper | * pins and jumper | ||
- | **===========================================================** | + | ---- |
+ | ==== License ==== | ||
+ | |||
+ | The Paper-USBasp was designed by **Wolfgang Spahn** 2013.\\ | ||
+ | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
+ | |||
+ | <html> | ||
+ | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
+ | </html> | ||
+ | |||
+ | ---- |