Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
avr_bootloader:avrdude [2015/10/17 13:33] admin created |
avr_bootloader:avrdude [2020/06/11 22:13] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ---- | + | ===== AVRdude & Arduino ===== |
- | **AVRdude** | + | |
- | ---- | + | |
- | AVRDUDE is a command line tool to program AVR chips. It runs in the background of the Arduino IDE. Sometimes it is necessary to erase a chip or set the fuse bits that's when the AVRdude comes handy. | + | AVRDUDE is a command line tool to program AVR chips. It runs in the background of the Arduino IDE. When burning the bootloader on an Arduino clone it is somtimes necessary to erase a chip or set the fuse bits manualy - that's when the AVRdude comes handy. |
Dokumentations:\\ | Dokumentations:\\ | ||
Line 42: | Line 40: | ||
Burning Serial to USB:\\ | Burning Serial to USB:\\ | ||
- | The hex file is in the arduino folder: /usr/share/arduino/hardware/arduino/firmwares/arduino-usbserial/Arduino-usbserial-uno.hex | + | The hex file is in the arduino folder: |
- | sudo avrdude -C /usr/share/arduino/hardware/tools/avrdude.conf -p m8u2 -c stk500v2 -P /dev/ttyACM0 -b115200 -U flash:w:Arduino-usbserial-uno.hex:i | + | cd /usr/share/arduino/hardware/arduino/firmwares/atmegaxxu2/arduino-usbserial/ |
+ | |||
+ | sudo avrdude -p m8u2 -c stk500v2 -P /dev/ttyACM0 -b115200 -U flash:w:Arduino-usbserial-uno.hex:i | ||
Burning Serial to USB on Sparkfun Atmega8u2 Breakout Board: | Burning Serial to USB on Sparkfun Atmega8u2 Breakout Board: | ||
Line 50: | Line 50: | ||
Burning Serial to Midi:\\ | Burning Serial to Midi:\\ | ||
The hex file is here: [[http://hunt.net.nz/users/darran/weblog/52882/Arduino_UNO_MIDI_USB_version_02.html]] | The hex file is here: [[http://hunt.net.nz/users/darran/weblog/52882/Arduino_UNO_MIDI_USB_version_02.html]] | ||
- | sudo avrdude -C /usr/share/arduino/hardware/tools/avrdude.conf -p m8u2 -c stk500v2 -P /dev/ttyACM0 -b115200 -U flash:w:MIDI_Firmware/Arduino-usbmidi-0.2.hex:i | + | sudo avrdude -p m8u2 -c stk500v2 -P /dev/ttyACM0 -b115200 -U flash:w:MIDI_Firmware/Arduino-usbmidi-0.2.hex:i |
+ | ---- | ||
+ | ==== License ==== | ||
+ | This manual was made by **Wolfgang Spahn** 2011-20.\\ | ||
+ | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
+ | <html> | ||
+ | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
+ | </html> | ||
+ | |||
+ | ---- | ||