Differences
This shows you the differences between two versions of the page.
arduino_clones:fabric-duino [2020/02/14 18:58] admin |
arduino_clones:fabric-duino [2020/06/11 22:13] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== Fabric-Duino ===== | ||
- | {{ :arduino_clones:fabric-duino_011229.jpg?400 |}}\\ | ||
- | The Fabric-Duino is an Arduino clone for fabric. And for connectors one can make small wire eye.\\ | ||
- | {{ :arduino_clones:duino-shirt.jpg?400 |}}\\ | ||
- | All Paper-Duino version will works as well, but the smaller version is much handier.\\ | ||
- | ---- | ||
- | ==== Paper PCB ==== | ||
- | {{:arduino_clones:fabric-duino_02.jpg?300|}}\\ | ||
- | {{ :arduino_clones:fabric-duino_02.zip |}}\\ | ||
- | |||
- | ---- | ||
- | ==== Workaround ==== | ||
- | 01. Iron the printout on fabric:\\ | ||
- | {{:arduino_clones:fabric-duino_01_174501.jpg?200|}}\\ | ||
- | 02. Cut a Copper-Stripe-Board to the right sice:\\ | ||
- | {{:arduino_clones:fabric-duino_02_181905.jpg?200|}}\\ | ||
- | 03. Solder all parts:\\ | ||
- | {{:arduino_clones:fabric-duino_03_194424.jpg?200|}}\\ | ||
- | The back should looks like that:\\ | ||
- | {{:arduino_clones:fabric-duino_03_back_194449.jpg?200|}}\\ | ||
- | For wireing parts like LEDs and switches one need some Conductive Thread and a needle.\\ | ||
- | |||
- | ---- | ||
- | ==== Software ==== | ||
- | One should first burn the bootloader on the chip: [[avr_bootloader:bootloader|Burning the Bootloader]]\\ | ||
- | For uploading a scetch one need a Serial to USB board or: [[arduino_clones:serial_adapter|The Arduino as a Serial Adapter]]\\ | ||
- | |||
- | ---- | ||
- | ==== Parts ==== | ||
- | * Atmega328 | ||
- | * 1 LED | ||
- | * voltage converter 7805 | ||
- | * crystal 16MHz | ||
- | * 1 elkos 100µF | ||
- | * 4 capacitors 100nF | ||
- | * 2 capacitors 22pF | ||
- | * diode 1N4007 | ||
- | * resistors: 1x 330Ohm, 2x 470Ohm, 1x 10kOhm | ||
- | * push button | ||
- | * pin headers & sockets | ||
- | * battery clip | ||
- | |||
- | ---- | ||
- | ==== License ==== | ||
- | |||
- | The Fabric-Duino was designed by **Wolfgang Spahn** 2017.\\ | ||
- | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
- | |||
- | <html> | ||
- | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
- | </html> | ||
- | |||
- | ---- |