Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
arduino_clones:fabric-duino [2016/06/13 19:34] admin |
arduino_clones:fabric-duino [2017/03/09 23:18] admin |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== Fabric-Duino ===== | ===== Fabric-Duino ===== | ||
| {{ :arduino_clones:fabric-duino_011229.jpg?400 |}}\\ | {{ :arduino_clones:fabric-duino_011229.jpg?400 |}}\\ | ||
| - | The Fabric-Duino is basically a version of the [[arduino_clones:paper-duino-mini|Paper-Duino-Mini]]. One use fabric instead of the paper. And as connector one make small wire eye.\\ | + | The Fabric-Duino is an Arduino clone for fabric. And for connectors one can make small wire eye.\\ |
| {{ :arduino_clones:duino-shirt.jpg?400 |}}\\ | {{ :arduino_clones:duino-shirt.jpg?400 |}}\\ | ||
| - | The Paper-Duino-UNO works as well, but the smaller version is much handier.\\ | + | All Paper-Duino version will works as well, but the smaller version is much handier.\\ |
| + | |||
| + | ---- | ||
| + | ==== Paper PCB ==== | ||
| + | {{:arduino_clones:fabric-duino_02.jpg?300|}}\\ | ||
| + | {{ :arduino_clones:fabric-duino_02.zip |}}\\ | ||
| + | |||
| + | ---- | ||
| + | ==== Workaround ==== | ||
| 01. Iron the printout on fabric:\\ | 01. Iron the printout on fabric:\\ | ||
| {{:arduino_clones:fabric-duino_01_174501.jpg?200|}}\\ | {{:arduino_clones:fabric-duino_01_174501.jpg?200|}}\\ | ||
| - | 02. Cut a Copper-Stripe-Board in the right sice:\\ | + | 02. Cut a Copper-Stripe-Board to the right sice:\\ |
| {{:arduino_clones:fabric-duino_02_181905.jpg?200|}}\\ | {{:arduino_clones:fabric-duino_02_181905.jpg?200|}}\\ | ||
| - | 03. Solder all parts in:\\ | + | 03. Solder all parts:\\ |
| {{:arduino_clones:fabric-duino_03_194424.jpg?200|}}\\ | {{:arduino_clones:fabric-duino_03_194424.jpg?200|}}\\ | ||
| The back should looks like that:\\ | The back should looks like that:\\ | ||
| {{:arduino_clones:fabric-duino_03_back_194449.jpg?200|}}\\ | {{:arduino_clones:fabric-duino_03_back_194449.jpg?200|}}\\ | ||
| + | For wireing parts like LEDs and switches one need some Conductive Thread and a needle.\\ | ||
| + | |||
| + | ---- | ||
| + | ==== Software ==== | ||
| + | One should first burn the bootloader on the chip: [[avr_bootloader:bootloader|Burning the Bootloader]]\\ | ||
| + | For uploading a scetch one need a Serial to USB board or: [[arduino_clones:serial_adapter|The Arduino as a Serial Adapter]]\\ | ||
| + | |||
| + | ---- | ||
| + | ==== Parts ==== | ||
| + | * Atmega328 | ||
| + | * 1 LED | ||
| + | * voltage converter 7805 | ||
| + | * crystal 16MHz | ||
| + | * 1 elkos 100µF | ||
| + | * 4 capacitors 100nF | ||
| + | * 2 capacitors 22pF | ||
| + | * diode 1N4007 | ||
| + | * resistors: 1x 330Ohm, 2x 470Ohm, 1x 10kOhm | ||
| + | * push button | ||
| + | * pin headers & sockets | ||
| + | * battery clip | ||
| ---- | ---- | ||
| - | For uploading a scetch one need the Adappter-Board and a Serial to USB board.\\ | + | ~~socialite:icon facebook twitter googleplus reddit tumblr~~ |
| - | {{:arduino_clones:fabric-duino_upload_194346.jpg?400|}}\\ | + | |
| - | ~~socialite:icon facebook twitter googleplus reddit~~ | + | |
| ---- | ---- | ||
| + | ~~DISCUSSION~~ | ||