Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
arduino_clones:bootloader [2012/09/23 20:48]
admin 		arduino_clones:bootloader [2015/10/17 13:31]
admin removed
Line 1: Line 1:
-**== Burning the Bootloader ​==============================**+---- 
 +**Burning the Bootloader ​with the Arduino IDE** 
 +----
  
-For burning the bootloader you need to connect ​these pins on your Paperduino-UNO with the programmer:+For burning the bootloader ​on the Paperduino-UNO,​ or on the Paper-Leonardo ​you need to connect ​the following ​pins on your Paperduino-UNO with your ISP programmer (in-system ​programmer):
   * 11 - MOSI   * 11 - MOSI
   * 12 - MISO   * 12 - MISO
Line 8: Line 10:
   * Ground   * Ground
   * + 5V   * + 5V
 +After connecting the programmer to your computer select in the Arduino IDE in Tools/​Programmer your programmer and than klick Tools/Burn Bootloader.
  
-**Burning the bootloader with an AVR programmer:**\\ +---- 
-Cause my ISP programmer (in-system programmer) has a different protokoll as the originale AVR-ISP programmer I had to modifie the file "​programmers.txt"​ in that folder:\\ +**With an AVR ISP programmer**
-/​usr/​share/​arduino/​hardware/​arduino.\\ +
-The third line has to change to:\\ +
-"​avrisp.protocol=stk500v1"​.\\ +
-On the foto you see the ISP programmer with an ISP adapter board.  +
- +
-{{ :​arduino_clones:​isp-header.jpg?​nolink&​100 |}}These are the connection of an original ISP header.+
  
 {{ :​arduino_clones:​isp_adapter.jpg?​direct&​300 |}} {{ :​arduino_clones:​isp_adapter.jpg?​direct&​300 |}}
  
-** Burning ​the bootoloader ​with an Arduino**\\ +On the foto you see the ISP programmer ​with an ISP adapter board. But you could also build your own modified wire like that on the [[http://​arduino.cc/​en/​Hacking/​MiniBootloader|Mini Bootloader project]]. Anyway here are the connection of an original ISP header.
-You can use your Arduino to burn the bootloder. Just load the ArduinoISP (in examples) on your Arduino. Connect the pins like that:+
  
 +{{:​arduino_clones:​isp-header.jpg?​nolink|}}
  
 +Cause my ISP programmer has a different protokoll as the originale AVR-ISP programmer I had to modifie the programmers.txt file.\\
 +In that folder(on Linux):
 +  /​usr/​share/​arduino/​hardware/​arduino
 +The third line has to change to:
 +  avrisp.protocol=stk500v1
  
 +
 +----
 +**With the Paper-USBasp programmer**
 +
 +It is simelar to the AVR ISP programmer, just select the USBasp programmer and burn.
 +
 +{{ :​avr_bootloader:​paper_usbasp_1274.jpg?​300 |}}
 +
 +Here is a manual for building your own [[avr_bootloader:​paper_usbasp|Paper-USBasp programmmer]].
 +
 +
 +----
 +**With a Paperduino-UNO**
 +
 +The Paperduino-UNO was designed for cloneing and that's why you can use your Paperduino-UNO fot burning bootloder, too. Just load the ArduinoISP - in the examples - on your Paperduino-UNO. After that, **turn off the auto reset by removeing the auto reset jumper**. And than connect the pins like that:
 +  * 13 to 13
 +  * 12 to 12
 +  * 11 to 11
 +  * 10 to Reset
 +  * Ground to Ground
 +  * +5V to +5V
 +... and than burn!
  
 {{ :​arduino_clones:​paperduino-uno_as_isp_adapter_wspahn.jpg?​direct&​300 |}} {{ :​arduino_clones:​paperduino-uno_as_isp_adapter_wspahn.jpg?​direct&​300 |}}
  
-**===========================================================**+---- 
 +** Burning the Bootloader with the AVRdude** 
 + 
 +Burning the bootloader on an Atmega328p chip of 
 +a Paperduino-Uno or a Paper-Duino-Pi with an AVR ISP programmer. 
 + 
 +Go to the folder with the bootloader. 
 + 
 +Run avrdude in command line: 
 +  $ sudo avrdude -p m328p -c stk500v2 -P /​dev/​ttyACM0 -U flash:​w:​optiboot_atmega328.hex:​i 
 +   
 +More at the [[arduino_clones:​AVRdude|AVRdude]] page. 
 + 
 +----