Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
arduino_clones:papercocomake7 [2018/05/11 17:58] admin [PaperCocoMake7] |
arduino_clones:papercocomake7 [2020/06/11 22:13] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ===== PaperCocoMake7 ===== | + | ===== Paper CocoMake7 ===== |
| - | The PaperCocoMake7 in an Arduino board based on Paper PCB and an ATtiny85 chip. It is the paper version of the [[https://cocomake7.github.io/#|CocoMake7]]. Like on the cocoMake7 one can upload code over the sound card of your PC.\\ | + | The PaperCocoMake7 in an Arduino board based on Paper PCB and an ATtiny85 chip. It is the paper version of the [[https://cocomake7.github.io/#|CocoMake7]]. |
| Thanks to Marc, Yashas, Shreyasi and Budi from [[https://cocomake7.github.io/#|Cocomake7]].\\ | Thanks to Marc, Yashas, Shreyasi and Budi from [[https://cocomake7.github.io/#|Cocomake7]].\\ | ||
| For code and the Arduino IDE mod please follow the [[https://cocomake7.github.io/#|CocoMake7 webside]].\\ | For code and the Arduino IDE mod please follow the [[https://cocomake7.github.io/#|CocoMake7 webside]].\\ | ||
| + | Here you find an other ATiny board the [[arduino_clones:papertiny|PaperTiny]].\\ | ||
| + | **Paper CocoMake7**\\ | ||
| {{:arduino_clones:papercocomake7.jpg?400|}}\\ | {{:arduino_clones:papercocomake7.jpg?400|}}\\ | ||
| + | |||
| + | **Paper CocoMake**\\ | ||
| + | {{:arduino_clones:papercocomake1.jpg?400|}}\\ | ||
| ---- | ---- | ||
| ==== Paper PCB ==== | ==== Paper PCB ==== | ||
| + | |||
| + | **Paper CocoMake7** with audio out and no power on board:\\ | ||
| {{:arduino_clones:papercocomake7_03.jpg?200|}}\\ | {{:arduino_clones:papercocomake7_03.jpg?200|}}\\ | ||
| - | {{ :arduino_clones:papercocomake7_03.zip |}} | + | {{ :arduino_clones:papercocomake7_03.zip |}}\\ |
| + | |||
| + | **Paper CocoMake** with power on board no audio out:\\ | ||
| + | {{:arduino_clones:papercocomake1_10.jpg?200|}}\\ | ||
| + | {{ :arduino_clones:papercocomake1_10.zip |}}\\ | ||
| + | |||
| + | ---- | ||
| + | ==== Schematic ==== | ||
| + | It's the same schematic as the one from [[https://cocomake7.github.io/#]], I just used 2k as the LED resistors and added a power supply.\\ | ||
| + | {{:arduino_clones:mrbaladuinoone_schematic.png?400|}}\\ | ||
| ---- | ---- | ||
| ==== Parts ==== | ==== Parts ==== | ||
| * **Resistors:** | * **Resistors:** | ||
| - | * 2x 220 Ohm | + | * 2x 2 kOhm |
| * 1x 1.5 kOhm | * 1x 1.5 kOhm | ||
| - | * 1x 47 kOhm | + | * 1x 47 kOhm(1) |
| * 2x 68 Ohm | * 2x 68 Ohm | ||
| * **Capacitors:** | * **Capacitors:** | ||
| - | * 1x 100 nF | + | * 2x 100 nF |
| + | * 1x 10µF(1) | ||
| + | * 1x 100µF(2) | ||
| * **Diodes:** | * **Diodes:** | ||
| * 2x Z-Diode 3,3V | * 2x Z-Diode 3,3V | ||
| * **Semiconductors** | * **Semiconductors** | ||
| * 2x Standart LED | * 2x Standart LED | ||
| + | * 1x 7805(2) | ||
| * **Mechanical:** | * **Mechanical:** | ||
| * 1x IC socket, 8pins | * 1x IC socket, 8pins | ||
| - | * 1x Pin-Strip male 1x2 | + | * 1x Pin-Strip male 1x2(2) |
| - | * 2x Pin-Strip male 1x4 | + | * 2x Pin-Strip female 1x4 |
| - | * jack socket | + | * jack socket(1) |
| + | (1) Paper CocoMake7\\ | ||
| + | (2) Paper CocoMake\\ | ||
| ---- | ---- | ||
| - | ==== Links & Knowledge ==== | + | ==== License ==== |
| - | ===ATtiny Projects:=== | + | The Paper CocoMake7 was designed by **Wolfgang Spahn** 2017-18.\\ |
| - | [[https://cocomake7.github.io/#|CocoMake7]]\\ | + | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. |
| - | [[http://digistump.com/wiki|Digispark]]\\ | + | |
| - | [[https://learn.adafruit.com/introducing-trinket/introduction|Trinket]]\\ | + | |
| - | ===Links:=== | + | <html> |
| - | [[https://learn.adafruit.com/usbtinyisp/avrdude#for-linux|USBTinyISP for Linux]]\\ | + | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> |
| - | + | </html> | |
| - | ===Technical Details:=== | + | |
| - | [[http://www.atmel.com/Images/Atmel-2586-AVR-8-bit-Microcontroller-ATtiny25-ATtiny45-ATtiny85_Datasheet.pdf|ATtiny85 Datasheet]]\\ | + | |
| - | + | ||
| - | {{:arduino_clones:usb_socket.jpg?200|}}\\ | + | |
| - | + | ||
| - | ---- | + | |
| - | ~~socialite:icon facebook twitter googleplus reddit tumblr~~ | + | |
| ---- | ---- | ||