Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
analog_computer:confetti101_gyrator [2019/06/28 19:53] admin created |
analog_computer:confetti101_gyrator [2020/06/11 22:13] (current) |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== Confetti101 Gyrator ===== | ===== Confetti101 Gyrator ===== | ||
| - | coming soon | + | That's a [[https://en.wikipedia.org/wiki/Gyrator|gyrator]] board for the analog computer [[analog_computer:analog_computer_main|Confetti]].\\ |
| + | With the jumper set one can connect the output to the common ground, if no jumper is used one can use the output connector instead.\\ | ||
| + | Together with the [[analog_computer:confetti102_chua_diode|Confetti102 Chua Diode]] one can build a [[https://en.wikipedia.org/wiki/Chua%27s_circuit|Chua's Oscillator]].\\ | ||
| + | |||
| + | {{:analog_computer:chua_s_circuit_pure_134355.jpg?600|}}\\ | ||
| + | [[https://dernulleffekt.de/doku.php?id=analogcomputation:01_chuascircuit#analog_computation_01_-_chua_s_circuit|Analog Computing 01 - Chua's Circuit]]\\ | ||
| + | |||
| + | |||
| + | ---- | ||
| + | ==== Paper PCB ==== | ||
| + | |||
| + | {{:analog_computer:confetti101_gyrator_03_15mh.jpg?400|}}\\ | ||
| + | {{ :analog_computer:confetti101_gyrator_03_15mh.zip |}}\\ | ||
| + | |||
| + | ---- | ||
| + | ==== Parts ==== | ||
| + | |||
| + | To build this board one needs a copper stripe protoboard (1/6 of the 16x10cm board), a paper print out (1:1) and some copper wire for the bridges. | ||
| + | |||
| + | * **Resistors:** | ||
| + | * 1x 100 Ohm | ||
| + | * 2x 1 kOhm | ||
| + | * **Capacitors:** | ||
| + | * 1x 100nF | ||
| + | * **Semiconductors** | ||
| + | * 1x TL072 OpAmp | ||
| + | * **Mechanical:** | ||
| + | * 1x IC socket, 8pins | ||
| + | * 1x 2 pin strip | ||
| + | * 1x 1 pin | ||
| + | * 3x 2 pin header, female | ||
| + | * 2x pin header, female 90° 1x3, 1x2 | ||
| + | * 2x pin header, male 90° 1x3, 1x2 | ||
| + | * 1x jumpers | ||
| + | * **Trimpotentiometer:** | ||
| + | * 1x 5 kOhm | ||
| + | |||
| + | ---- | ||
| + | ==== License ==== | ||
| + | |||
| + | The Confetti101 Gyrator was designed by **Wolfgang Spahn** 2015-20.\\ | ||
| + | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
| + | |||
| + | <html> | ||
| + | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
| + | </html> | ||
| ---- | ---- | ||