Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
raspberry_boards:paperduinopi_hat [2016/07/16 22:32] admin |
raspberry_boards:paperduinopi_hat [2016/07/17 01:57] admin [Install the Shutdown Button and the LED] |
||
|---|---|---|---|
| Line 11: | Line 11: | ||
| {{:raspberry_boards:paper-duino-pi_51.jpg?400|}}\\ | {{:raspberry_boards:paper-duino-pi_51.jpg?400|}}\\ | ||
| {{:raspberry_boards:paper-duino-pi_51.ai.zip|}}\\ | {{:raspberry_boards:paper-duino-pi_51.ai.zip|}}\\ | ||
| + | |||
| + | ---- | ||
| + | |||
| + | ==== Parts ==== | ||
| + | * Atmega328p | ||
| + | * 28 pin IC socket | ||
| + | * 4x low current LEDs | ||
| + | * crystal 16MHz | ||
| + | * 2x capacitors 100nF | ||
| + | * 2x capacitors 22pF | ||
| + | * capacitor 68nF | ||
| + | * 2x Z-diode 3.3V | ||
| + | * resistors: 2x 2kOhm, 4x 1kOhm, 1x 6.8kOhm | ||
| + | * 2x reset button | ||
| + | * one row headers, 2x8, 2x3, 1x4 | ||
| + | * a 2x8 pin header | ||
| ---- | ---- | ||
| Line 28: | Line 44: | ||
| $ mkdir paper-duino-pi | $ mkdir paper-duino-pi | ||
| $ cd paper-duino-pi | $ cd paper-duino-pi | ||
| - | Download and unpack the files: | + | Download the files: |
| $ wget http://dernulleffekt.de/programme/paperduinopi_v05/paper-duino-hat_01.tar.gz | $ wget http://dernulleffekt.de/programme/paperduinopi_v05/paper-duino-hat_01.tar.gz | ||
| - | $ tar -xvf paper-duino-pi_Pi2_Jessy.tar.gz | + | And unpack: |
| + | $ tar -xvf paper-duino-hat_01.tar.gz | ||
| Run the setup: | Run the setup: | ||
| $ sudo chmod 755 setup | $ sudo chmod 755 setup | ||
| Line 59: | Line 76: | ||
| $ sudo nano /etc/rc.local | $ sudo nano /etc/rc.local | ||
| Write before "exit 0": | Write before "exit 0": | ||
| - | # run reset and shutdown script | + | printf "<<<<<<<< PAPER-DUINO-HAT\n" |
| - | printf "Starts shutdown aund reset button on GPIO 22\n" | + | printf "<<<<<<<< 07_2016 http://dernulleffekt.de\n" |
| - | /home/pi/paper-duino-pi/shutdownbutton_hat.py & | + | |
| - | # blink an LED | + | # run reset and shutdown script |
| - | printf "Starts blinking LED on GPIO 27\n" | + | printf "<<<<<<<< Starting shutdown aund reset button on GPIO 22\n" |
| - | /home/pi/paper-duino-pi/blink_hat.py & | + | /home/pi/paper-duino-pi/shutdownbutton_hat.py & |
| + | |||
| + | # blink an LED | ||
| + | printf "<<<<<<<< Starting blinking LED on GPIO 27\n" | ||
| + | /home/pi/paper-duino-pi/blink_hat.py & | ||
| To save and leave press: CTRL+O, Enter, CTRL+X\\ | To save and leave press: CTRL+O, Enter, CTRL+X\\ | ||
| Reboot: | Reboot: | ||
| Line 74: | Line 96: | ||
| {{:raspberry_boards:spi-connection_202802.jpg?400|}}\\ | {{:raspberry_boards:spi-connection_202802.jpg?400|}}\\ | ||
| - | Raspberry Pi | Arduino | + | Raspberry Pi | Paper-Duino-Hat |
| ====================================== | ====================================== | ||
| MOSI (GPIO 10) | MOSI (pin 11) | MOSI (GPIO 10) | MOSI (pin 11) | ||
| Line 81: | Line 103: | ||
| RST (GPIO 25) | Reset | RST (GPIO 25) | Reset | ||
| GND | GND | GND | GND | ||
| - | 3.3V | 3,3V | + | 3.3V | 5V |
| Run on the following commands:\\ | Run on the following commands:\\ | ||
| Line 97: | Line 119: | ||
| ---- | ---- | ||
| - | {{:raspberry_boards:paper-duino-hat_212231.jpg?400|}}\\ | ||
| ~~socialite:icon facebook twitter googleplus reddit~~ | ~~socialite:icon facebook twitter googleplus reddit~~ | ||
| ---- | ---- | ||