Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
avr_bootloader:paper_usbasp [2013/03/22 22:29] admin |
avr_bootloader:paper_usbasp [2016/09/12 17:20] admin |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | **== USBasp Board ======================================** | + | ===== Paper-USBasp ===== |
| - | That board based on the [[http://www.fischl.de/usbasp/|USBasp Board]] of [[http://www.fischl.de|Thomas Fischl]]. There one find all schematics and manuals for the board.\\ | + | The Paper-USBasp is a Paper-PCB version of an USB in-circuit programmer for Atmel AVR controllers. The board based on the [[http://www.fischl.de/usbasp/|USBasp Board]] of [[http://www.fischl.de|Thomas Fischl]]. |
| - | \\ | + | |
| On the paper version the serial connection (RX and TX) were removed. A jumper for 3.6V was added. | On the paper version the serial connection (RX and TX) were removed. A jumper for 3.6V was added. | ||
| - | **== Paper-PCB ============================================** | + | The Paper USBasp can be perfectly combined with the [[avr_bootloader:programming_board|Programming Board]] for programming AVR chips: |
| + | |||
| + | {{ :avr_bootloader:paper_usbasp_-_programmer_board_1265.jpg?300 |}} | ||
| + | |||
| + | Or certainly it can be used to burn your bootloader on your [[arduino_clones:paperduino-uno|Paperduino-Uno]]: | ||
| + | |||
| + | {{ :avr_bootloader:paper_usbasp_1274.jpg?300 |}} | ||
| + | |||
| + | Here: [[http://www.fundf.net/usbasp/]] one find all schematics and manuals for the original USBasp board. They are similar to the paper version of the programmer. | ||
| + | |||
| + | Front: | ||
| + | |||
| + | {{:avr_bootloader:paper_usbasp_front_1266.jpg?200|}} | ||
| + | |||
| + | Back: | ||
| + | |||
| + | {{:avr_bootloader:paper_usbasp_back_1267.jpg?200|}} | ||
| + | |||
| + | Here is a manual for [[avr_bootloader:burning_firmware|burning the firmware]] | ||
| + | |||
| + | ---- | ||
| + | ==== Paper-PCB ==== | ||
| {{:avr_bootloader:paper-usbasp_20_pub_stripes.jpg?200|}}\\ | {{:avr_bootloader:paper-usbasp_20_pub_stripes.jpg?200|}}\\ | ||
| {{:avr_bootloader:paper-usbasp_20_pub.jpg?200|}}\\ | {{:avr_bootloader:paper-usbasp_20_pub.jpg?200|}}\\ | ||
| {{:avr_bootloader:paper-usbasp_20_pub.xcf.zip|}}\\ | {{:avr_bootloader:paper-usbasp_20_pub.xcf.zip|}}\\ | ||
| - | **== Components ===========================================** | + | ---- |
| + | ==== Parts ==== | ||
| * Atmega8 or Atmega48 | * Atmega8 or Atmega48 | ||
| * IC socket, 28 pin | * IC socket, 28 pin | ||
| Line 25: | Line 46: | ||
| * pins and jumper | * pins and jumper | ||
| - | **===========================================================** | + | ---- |
| + | ~~socialite:icon facebook twitter googleplus reddit tumblr~~ | ||
| + | |||
| + | ---- | ||
| + | ~~DISCUSSION~~ | ||