Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
arduino_clones:papercocomake7 [2018/05/25 18:29] admin [Parts] |
arduino_clones:papercocomake7 [2019/01/04 20:45] admin [Schematic] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== PaperCocoMake7 ===== | + | ===== Paper CocoMake7 ===== |
The PaperCocoMake7 in an Arduino board based on Paper PCB and an ATtiny85 chip. It is the paper version of the [[https://cocomake7.github.io/#|CocoMake7]]. | The PaperCocoMake7 in an Arduino board based on Paper PCB and an ATtiny85 chip. It is the paper version of the [[https://cocomake7.github.io/#|CocoMake7]]. | ||
Line 6: | Line 6: | ||
Here you find an other ATiny board the [[arduino_clones:papertiny|PaperTiny]].\\ | Here you find an other ATiny board the [[arduino_clones:papertiny|PaperTiny]].\\ | ||
- | {{:arduino_clones:papercocomake7.jpg|}}\\ | + | **Paper CocoMake7**\\ |
+ | {{:arduino_clones:papercocomake7.jpg?400|}}\\ | ||
+ | |||
+ | **Paper CocoMake**\\ | ||
+ | {{:arduino_clones:papercocomake1.jpg?400|}}\\ | ||
---- | ---- | ||
==== Paper PCB ==== | ==== Paper PCB ==== | ||
- | **with audio out and no power on board:**\\ | + | **Paper CocoMake7** with audio out and no power on board:\\ |
{{:arduino_clones:papercocomake7_03.jpg?200|}}\\ | {{:arduino_clones:papercocomake7_03.jpg?200|}}\\ | ||
{{ :arduino_clones:papercocomake7_03.zip |}}\\ | {{ :arduino_clones:papercocomake7_03.zip |}}\\ | ||
- | **without audio out and power on board:**\\ | + | **Paper CocoMake** with power on board no audio out:\\ |
{{:arduino_clones:papercocomake1_10.jpg?200|}}\\ | {{:arduino_clones:papercocomake1_10.jpg?200|}}\\ | ||
{{ :arduino_clones:papercocomake1_10.zip |}}\\ | {{ :arduino_clones:papercocomake1_10.zip |}}\\ | ||
Line 20: | Line 24: | ||
---- | ---- | ||
==== Schematic ==== | ==== Schematic ==== | ||
- | It's the one from [[https://cocomake7.github.io/#]], I just used 2k resistors for the LED resistors and added a power supply.\\ | + | It's the same schematic as the one from [[https://cocomake7.github.io/#]], I just used 2k as the LED resistors and added a power supply.\\ |
{{:arduino_clones:mrbaladuinoone_schematic.png?400|}}\\ | {{:arduino_clones:mrbaladuinoone_schematic.png?400|}}\\ | ||
Line 28: | Line 32: | ||
* 2x 2 kOhm | * 2x 2 kOhm | ||
* 1x 1.5 kOhm | * 1x 1.5 kOhm | ||
- | * 1x 47 kOhm* | + | * 1x 47 kOhm(1) |
* 2x 68 Ohm | * 2x 68 Ohm | ||
* **Capacitors:** | * **Capacitors:** | ||
* 2x 100 nF | * 2x 100 nF | ||
- | * 1x 10µF* | + | * 1x 10µF(1) |
- | * 1x 100µF** | + | * 1x 100µF(2) |
* **Diodes:** | * **Diodes:** | ||
* 2x Z-Diode 3,3V | * 2x Z-Diode 3,3V | ||
* **Semiconductors** | * **Semiconductors** | ||
* 2x Standart LED | * 2x Standart LED | ||
- | * 1x 7805** | + | * 1x 7805(2) |
* **Mechanical:** | * **Mechanical:** | ||
* 1x IC socket, 8pins | * 1x IC socket, 8pins | ||
- | * 1x Pin-Strip male 1x2** | + | * 1x Pin-Strip male 1x2(2) |
* 2x Pin-Strip female 1x4 | * 2x Pin-Strip female 1x4 | ||
- | * jack socket* | + | * jack socket(1) |
+ | (1) Paper CocoMake7\\ | ||
+ | (2) Paper CocoMake\\ | ||
---- | ---- |