Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
raspberry_boards:raspi-sound-hat [2020/03/05 01:24] admin |
raspberry_boards:raspi-sound-hat [2020/09/01 19:25] (current) admin [Alsa Mixer Settings] |
||
---|---|---|---|
Line 42: | Line 42: | ||
* 1x 12 MHz | * 1x 12 MHz | ||
* **Semiconductors** | * **Semiconductors** | ||
- | * 1x LD117 (3V3) | + | * 1x LD1117V33 (3V3 version!) |
* 1x WM8731 | * 1x WM8731 | ||
* **Mechanical:** | * **Mechanical:** | ||
Line 55: | Line 55: | ||
==== Installation === | ==== Installation === | ||
- | After connecting the Audio Injector to the Raspberry Pi change some configurations, in: | + | After connecting the Audio Injector to the Raspberry Pi some software should be installed.\\ |
+ | First you have to download the deb package from [[http://forum.audioinjector.net/viewtopic.php?f=5&t=3]]. | ||
+ | $ wget https://github.com/Audio-Injector/stereo-and-zero/archive/master.zip | ||
+ | Unpack it: | ||
+ | $ unzip master.zip | ||
+ | And install it: | ||
+ | $ cd stereo-and-zero-master/ | ||
+ | $ sudo apt install ./audio.injector.scripts_0.1-1_all.deb | ||
+ | Change some configurations, in: | ||
$ sudo nano /boot/config.txt | $ sudo nano /boot/config.txt | ||
- | Comment out: | + | Put in comment: |
# dtparam=audio=on | # dtparam=audio=on | ||
And type in: | And type in: | ||
+ | # Enable audio (WM8731) | ||
dtoverlay=audioinjector-wm8731-audio | dtoverlay=audioinjector-wm8731-audio | ||
ctl + o for saving, press return and ctl + x to leave.\\ | ctl + o for saving, press return and ctl + x to leave.\\ | ||
Line 68: | Line 77: | ||
==== Alsa Mixer Settings ==== | ==== Alsa Mixer Settings ==== | ||
- | [[https://github.com/Audio-Injector/stereo-and-zero]]\\ | + | To enable the audio output: |
- | There are two reference alsa mixer files which will allow you to setup default output with either line input or microphone input : | + | $ amixer set 'Output Mixer HiFi' on |
- | Download: | + | Go into the folder: |
- | $ wget https://github.com/Audio-Injector/stereo-and-zero/archive/master.zip | + | $ cd stereo-and-zero-master/audio.injector.scripts-0.1/ |
- | Unpack it: | + | To setup the output run the following command: |
- | $ unzip master.zip | + | In combination with the microphone input: |
- | go into the folder: | + | |
- | $ cd stereo-and-zero-master/ | + | |
- | and run: | + | |
$ alsactl --file asound.state.MIC.thru.test restore | $ alsactl --file asound.state.MIC.thru.test restore | ||
+ | or in combination with the lines input: | ||
$ alsactl --file asound.state.RCA.thru.test restore | $ alsactl --file asound.state.RCA.thru.test restore | ||
+ | to check the alsa setting: | ||
+ | $ alsamixer | ||
---- | ---- | ||
Line 159: | Line 168: | ||
[[https://github.com/Audio-Injector/stereo-and-zero]]\\ | [[https://github.com/Audio-Injector/stereo-and-zero]]\\ | ||
[[https://learn.adafruit.com/adafruit-max98357-i2s-class-d-mono-amp/raspberry-pi-usage]]\\ | [[https://learn.adafruit.com/adafruit-max98357-i2s-class-d-mono-amp/raspberry-pi-usage]]\\ | ||
+ | [[https://alsa-project.org/wiki/Main_Page]]\\ | ||
---- | ---- |