Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
raspberry_boards:paperduinopi_hat [2016/07/16 22:35]
admin [Paper PCB]
raspberry_boards:paperduinopi_hat [2020/06/11 22:13] (current)
Line 22: Line 22:
   * 2x capacitors 22pF   * 2x capacitors 22pF
   * capacitor 68nF   * capacitor 68nF
-  * resistors: ​3x 2kOhm, ​3x 1kOhm, 1x 6.8kOhm+  ​* 2x Z-diode 3.3V 
 +  ​* resistors: ​2x 2kOhm, ​4x 1kOhm, 1x 6.8kOhm
   * 2x reset button   * 2x reset button
-  * headers+  * one row headers, 2x8, 2x3, 1x4
   * a 2x8 pin header   * a 2x8 pin header
-  * resisters:​1x 330Ohm, 1x 10kOhm ​ 
  
 ---- ----
Line 44: Line 44:
   $ mkdir paper-duino-pi   $ mkdir paper-duino-pi
   $ cd paper-duino-pi   $ cd paper-duino-pi
-Download ​and unpack ​the files:+Download the files:
   $ wget http://​dernulleffekt.de/​programme/​paperduinopi_v05/​paper-duino-hat_01.tar.gz   $ wget http://​dernulleffekt.de/​programme/​paperduinopi_v05/​paper-duino-hat_01.tar.gz
-  ​$ tar -xvf paper-duino-pi_Pi2_Jessy.tar.gz+And unpack: 
 +  ​$ tar -xvf paper-duino-hat_01.tar.gz
 Run the setup: Run the setup:
   $ sudo chmod 755 setup   $ sudo chmod 755 setup
Line 75: Line 76:
     $ sudo nano /​etc/​rc.local     $ sudo nano /​etc/​rc.local
 Write before "exit 0": Write before "exit 0":
-   # run reset and shutdown script +  printf ">>>>>>>>​ PAPER-DUINO-HAT 07_2016 http://​dernulleffekt.de\n" ​           
-   ​printf "Starts ​shutdown aund reset button on GPIO 22\n"​ +   
-   ​/​home/​pi/​paper-duino-pi/​shutdownbutton_hat.py &  +  ​# run reset and shutdown script 
-   ​# blink an LED +  printf ">>>>>>>>​ Starting ​shutdown aund reset button on GPIO 22\n"​ 
-   ​printf "Starts ​blinking LED on GPIO 27\n"​ +  /​home/​pi/​paper-duino-pi/​shutdownbutton_hat.py &  
-   ​/​home/​pi/​paper-duino-pi/​blink_hat.py &+   
 +  ​# blink an LED 
 +  printf ">>>>>>>>​ Starting ​blinking LED on GPIO 27\n"​ 
 +  /​home/​pi/​paper-duino-pi/​blink_hat.py & 
 To save and leave press: CTRL+O, Enter, CTRL+X\\ To save and leave press: CTRL+O, Enter, CTRL+X\\
 Reboot: Reboot:
Line 90: Line 95:
 {{:​raspberry_boards:​spi-connection_202802.jpg?​400|}}\\ {{:​raspberry_boards:​spi-connection_202802.jpg?​400|}}\\
  
-   ​Raspberry Pi    |       Arduino+   ​Raspberry Pi    |       Paper-Duino-Hat
    ​======================================    ​======================================
    MOSI (GPIO 10)  |       MOSI (pin 11)    MOSI (GPIO 10)  |       MOSI (pin 11)
Line 97: Line 102:
    ​RST ​ (GPIO 25)  |       Reset    ​RST ​ (GPIO 25)  |       Reset
    ​GND ​            ​| ​      GND    ​GND ​            ​| ​      GND
-   ​3.3V ​           |       3,3V+   ​3.3V ​           |       5V
  
 Run on the following commands:\\ Run on the following commands:\\
Line 113: Line 118:
  
 ---- ----
-{{:​raspberry_boards:​paper-duino-hat_212231.jpg?400|}}\\ +==== License ==== 
-~~socialite:icon facebook twitter googleplus reddit~~+ 
 +The Paper-Duino-Hat was designed by **Wolfgang Spahn** 2012-16.\\ 
 +It is licensed under a [[http://​creativecommons.org/​licenses/​by-nc-sa/​4.0/"​|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. 
 + 
 +<​html>​ 
 +<a rel="​license"​ href="​http://​creativecommons.org/​licenses/​by-nc-sa/​4.0/"><​img alt="​Creative Commons License"​ style="​border-width:​0"​ src="​https://​i.creativecommons.org/​l/​by-nc-sa/​4.0/​88x31.png"​ /></​a>​  
 +</​html>​
  
 ---- ----
 +