Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
raspberry_boards:paperduinopi_168 [2014/07/23 15:34]
admin
raspberry_boards:paperduinopi_168 [2020/06/11 22:13] (current)
Line 1: Line 1:
----- +===== Paper-Duino-Pi 168 =====
-**Paper-Duino-Pi 168**+
  
 You find a general introduction here: You find a general introduction here:
Line 6: Line 5:
  
 {{:​raspberry_boards:​paper-duino-pi_0972.jpg?​300|}} {{:​raspberry_boards:​paper-duino-pi_0972.jpg?​300|}}
- 
----- 
-**Technical Documentation** 
  
 Unfortunately one can't use the autoreset function of an actual Arduino, because of the missing DTR line on the serial connector of the Raspberry. Therefore the board was designed with the Atmega 168. With that chip one can burn the bootloader of the old Arduino NG. That Arduino has no autoreset but doesn'​t need one. That's why you have to reset the Arduino manually to upload a program. After the IDE compiled the sketch you have to reset the Arduino. Once you've done this the IDE starts to upload the program. Unfortunately one can't use the autoreset function of an actual Arduino, because of the missing DTR line on the serial connector of the Raspberry. Therefore the board was designed with the Atmega 168. With that chip one can burn the bootloader of the old Arduino NG. That Arduino has no autoreset but doesn'​t need one. That's why you have to reset the Arduino manually to upload a program. After the IDE compiled the sketch you have to reset the Arduino. Once you've done this the IDE starts to upload the program.
Line 24: Line 20:
  
 ---- ----
-**Linux Modification**+==== Linux Modification ​====
  
 For using the serial line of the Raspberry Pi you have to make some small modifications:​ For using the serial line of the Raspberry Pi you have to make some small modifications:​
Line 52: Line 48:
  
 ---- ----
-**Paper-PCBs**+==== Paper-PCBs ​====
  
-{{:​raspberry_boards:​paper-duino-pi_13.jpg?​100|}}+{{:​raspberry_boards:​paper-duino-pi_13.jpg?​300|}}
  
 {{:​raspberry_boards:​paper-duino-pi_13_publish.xcf.zip|paper-duino-pi_13.zip}} {{:​raspberry_boards:​paper-duino-pi_13_publish.xcf.zip|paper-duino-pi_13.zip}}
  
 ---- ----
-**Components**+==== Parts ====
   * Atmega168   * Atmega168
   * 4 low current LEDs   * 4 low current LEDs
Line 69: Line 65:
   * headers   * headers
   * 26 pin header   * 26 pin header
 +
 +----
 +==== License ====
 +
 +The Paper-Duino-Pi 168 was designed by **Wolfgang Spahn** 2012.\\
 +It is licensed under a [[http://​creativecommons.org/​licenses/​by-nc-sa/​4.0/"​|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]].
 +
 +<​html>​
 +<a rel="​license"​ href="​http://​creativecommons.org/​licenses/​by-nc-sa/​4.0/"><​img alt="​Creative Commons License"​ style="​border-width:​0"​ src="​https://​i.creativecommons.org/​l/​by-nc-sa/​4.0/​88x31.png"​ /></​a> ​
 +</​html>​
  
 ---- ----