Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
raspberry_boards:duino-pi_modification [2016/01/20 21:48] admin [Install Shutdown & Reset Button] |
raspberry_boards:duino-pi_modification [2020/06/11 22:13] (current) |
||
---|---|---|---|
Line 7: | Line 7: | ||
---- | ---- | ||
- | ==== Change the user and the password ==== | ||
- | |||
- | [[http://raspi.tv/2012/how-to-create-a-new-user-on-raspberry-pi|How to create a new user]] | ||
- | |||
- | 1. Change the name: | ||
- | $ sudo nano /etc/hostname | ||
- | in "duino-pi"\\ | ||
- | |||
- | 2. Change the host file | ||
- | $ sudo nano /etc/hosts | ||
- | in: | ||
- | 127.0.0.1 localhost | ||
- | ::1 localhost ip6-localhost ip6-loopback | ||
- | fe00::0 ip6-localnet | ||
- | ff00::0 ip6-mcastprefix | ||
- | ff02::1 ip6-allnodes | ||
- | ff02::2 ip6-allrouters | ||
- | | ||
- | 127.0.1.1 duino-pi | ||
- | |||
- | 5. Change the password | ||
- | $ passwd | ||
- | |||
- | The passwd command allows you to change your password, you will be prompted for your old password, then you new password twice. The password is "dernulleffekt". | ||
- | |||
- | 4. Reboot: | ||
- | $ sudo reboot | ||
- | |||
- | ---- | ||
==== Install Shutdown & Reset Button ==== | ==== Install Shutdown & Reset Button ==== | ||
Line 43: | Line 14: | ||
2. Download and unzip that Python script | 2. Download and unzip that Python script | ||
- | <del>$ wget http://www.dernulleffekt.de/programme/shutdownbutton.py.tar.gz</del> | ||
$ wget http://www.dernulleffekt.de/programme/shutdownbutton_02.py.tar | $ wget http://www.dernulleffekt.de/programme/shutdownbutton_02.py.tar | ||
- | $ tar xf shutdownbutton.py.tar.gz | + | $ tar xf shutdownbutton_02.py.tar |
| | ||
2. Change owner & rights | 2. Change owner & rights | ||
Line 63: | Line 33: | ||
4. Reboot | 4. Reboot | ||
$ sudo reboot | $ sudo reboot | ||
- | \\ | + | |
+ | ---- | ||
+ | ==== Install Blinking LED ==== | ||
+ | |||
+ | 1. Make an folder (if not existing) | ||
+ | $ mkdir /home/pi/paper-duino-pi | ||
+ | $ cd /home/pi/paper-duino-pi | ||
+ | |||
+ | 2. Download and unzip that Python script | ||
+ | $ wget http://www.dernulleffekt.de/programme/blink_22.py.tar.gz | ||
+ | $ tar xf blink_22.py.tar.gz | ||
+ | |||
+ | 2. Change owner & rights | ||
+ | $ sudo chown root:root blink_22.py | ||
+ | $ sudo chmod 755 blink_22.py | ||
+ | |||
+ | 3. Create the autostart: | ||
+ | $ sudo nano /etc/rc.local | ||
+ | write before exit 0: | ||
+ | # blink an LED | ||
+ | printf "Starting blinking LED on GPIO 22" | ||
+ | /home/pi/paper-duino-pi/blink_22.py & | ||
+ | |||
+ | To save and leave press:\\ | ||
+ | CTRL+O, Enter, CTRL+X\\ | ||
+ | |||
+ | 4. Reboot | ||
+ | $ sudo reboot | ||
---- | ---- | ||
Line 140: | Line 137: | ||
---- | ---- | ||
- | ==== Set the SSH connection ==== | ||
- | |||
- | 1. For activating the SSH connection open | ||
- | $ sudo raspi-config | ||
- | In 8. Advanced Options you can activate SSH | ||
- | |||
- | 2. Give the Raspberry Pi an IP address. Open the interfaces file: | ||
- | $ sudo nano /etc/network/interfaces | ||
- | Change the DHCP in static and add these lines: | ||
- | |||
- | iface eth0 inet static | ||
- | address 192.168.0.111 | ||
- | netmask 255.255.255.0 | ||
- | gateway 192.168.0.100 | ||
- | |||
- | To save and leave press:\\ | ||
- | CTRL+O, Enter, CTRL+X | ||
- | |||
- | 3. Restart ethernet | ||
- | $ sudo ifdown eth0 | ||
- | $ sudo ifup eth0 | ||
- | |||
- | 3. Now you can login on your computer with: | ||
- | $ ssh duino-pi@192.168.0.111 | ||
- | or with XWindows support: | ||
- | $ ssh -XY pi@192.168.0.111 | ||
- | PW: raspberry\\ | ||
- | |||
- | ---- | ||
- | |||