Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
arduino_clones:papertiny [2018/05/25 18:41] admin [Firmware] |
arduino_clones:papertiny [2020/06/11 22:13] (current) |
||
|---|---|---|---|
| Line 18: | Line 18: | ||
| You can either use the Digispark bootloader together with the Digispart IDE modification or the Adafruit bootloader with the Adafruit software.\\ | You can either use the Digispark bootloader together with the Digispart IDE modification or the Adafruit bootloader with the Adafruit software.\\ | ||
| - | ====Burn The Adafruit Bootloader=== | + | ===Burn The Adafruit Bootloader=== |
| Download the bootloader from here: [[https://github.com/adafruit/Adafruit-Trinket-Gemma-Bootloader]], unpack it and cd to the folder.\\ | Download the bootloader from here: [[https://github.com/adafruit/Adafruit-Trinket-Gemma-Bootloader]], unpack it and cd to the folder.\\ | ||
| $ cd to_your_folder.../Adafruit\ Trinket/Adafruit-Trinket-Gemma-Bootloader-master/ | $ cd to_your_folder.../Adafruit\ Trinket/Adafruit-Trinket-Gemma-Bootloader-master/ | ||
| - | With an AVR Programmer or a Paperduino [[avr_bootloader:bootloader|burn the bootloader]]. Connect the SCK, MISO, MOSI, Reset, GND and +5V pins. If the avrdude is installed run the following commands in your terminal. If avrdude is not installed run "sudo apt-get install avrdude" or "sudo pacman -S avrdude" depending on your linux. Depending on your programmer use for "-c" your protocol and for "-P" the port on your computer. For "-p" write t85 it stand for your chip the ATiny.\\ | + | With an AVR Programmer or a Paperduino [[avr_bootloader:bootloader|burn the bootloader]]. Connect the SCK, MISO, MOSI, Reset, GND and +5V pins. If the avrdude is installed run the following commands in your terminal.\\ |
| + | If avrdude is not installed run "sudo apt-get install avrdude" or "sudo pacman -S avrdude" depending on your linux. Depending on your programmer use for "-c" your protocol and for "-P" the port on your computer. For "-p" write t85 it stand for your chip the ATiny.\\ | ||
| 1. Erase the chip: | 1. Erase the chip: | ||
| $ sudo avrdude -p t85 -c stk500v2 -P /dev/ttyACM0 -e | $ sudo avrdude -p t85 -c stk500v2 -P /dev/ttyACM0 -e | ||
| Line 30: | Line 31: | ||
| - | ====Burn The Digispark Bootloader=== | + | ===Burn The Digispark Bootloader=== |
| Download the bootloader from here: [[https://github.com/micronucleus/micronucleus]], unpack it and cd to the folder.\\ | Download the bootloader from here: [[https://github.com/micronucleus/micronucleus]], unpack it and cd to the folder.\\ | ||
| + | On Debian together with Arduin 1.8.5 use the old 2.01 version of the bootloader: [[https://github.com/micronucleus/micronucleus/releases/tag/v2.01]]\\ | ||
| $ cd to_your_folder.../micronucleus-master/firmware/releases/ | $ cd to_your_folder.../micronucleus-master/firmware/releases/ | ||
| - | With an AVR Programmer or a Paperduino [[avr_bootloader:bootloader|burn the bootloader]]. Connect the SCK, MISO, MOSI, Reset, GND and +5V pins. If the avrdude is installed run the following commands in your terminal. If avrdude is not installed run "sudo apt-get install avrdude" or "sudo pacman -S avrdude" depending on your linux. Depending on your programmer use for "-c" your protocol and for "-P" the port on your computer. For "-p" write t85 it stand for your chip the ATiny.\\ | + | With an AVR Programmer or a Paperduino [[avr_bootloader:bootloader|burn the bootloader]]. Connect the SCK, MISO, MOSI, Reset, GND and +5V pins.\\ |
| + | If the avrdude is installed run the following commands in your terminal. If avrdude is not installed run "sudo apt-get install avrdude" or "sudo pacman -S avrdude" depending on your linux. Depending on your programmer use for "-c" your protocol and for "-P" the port on your computer. For "-p" write t85 it stand for your chip the ATiny.\\ | ||
| 1. Erase the chip: | 1. Erase the chip: | ||
| $ sudo avrdude -p t85 -c stk500v2 -P /dev/ttyACM0 -e | $ sudo avrdude -p t85 -c stk500v2 -P /dev/ttyACM0 -e | ||
| Line 46: | Line 49: | ||
| or the instruction of the Adafruit Trinket board:\\ | or the instruction of the Adafruit Trinket board:\\ | ||
| [[https://learn.adafruit.com/introducing-trinket/introduction]]\\ | [[https://learn.adafruit.com/introducing-trinket/introduction]]\\ | ||
| + | **Select the "Adafruit Trinket 8MHz" board from Tools/Board and "USBtinyISP" from Tools/Programmer.** | ||
| ---- | ---- | ||
| ==== Schematic ==== | ==== Schematic ==== | ||
| Line 79: | Line 82: | ||
| [[https://cocomake7.github.io/#]]\\ | [[https://cocomake7.github.io/#]]\\ | ||
| [[http://digistump.com/wiki]]\\ | [[http://digistump.com/wiki]]\\ | ||
| - | [[http://highlowtech.org/?p=1695]] | + | [[http://highlowtech.org/?p=1695]]\\ |
| - | + | ||
| - | === Adafruit Trinket=== | + | |
| [[https://learn.adafruit.com/introducing-trinket/introduction]]\\ | [[https://learn.adafruit.com/introducing-trinket/introduction]]\\ | ||
| - | [[https://learn.adafruit.com/introducing-trinket/setting-up-with-arduino-ide]]\\ | ||
| - | [[https://github.com/adafruit/Adafruit-Trinket-Gemma-Bootloader]]\\ | ||
| [[https://learn.adafruit.com/usbtinyisp/avrdude#for-linux|USBTinyISP for Linux]]\\ | [[https://learn.adafruit.com/usbtinyisp/avrdude#for-linux|USBTinyISP for Linux]]\\ | ||
| ===Technical Details:=== | ===Technical Details:=== | ||
| + | |||
| + | {{:arduino_clones:attiny_pinout.png?600|}}\\ | ||
| + | |||
| [[http://www.atmel.com/Images/Atmel-2586-AVR-8-bit-Microcontroller-ATtiny25-ATtiny45-ATtiny85_Datasheet.pdf|ATtiny85 Datasheet]]\\ | [[http://www.atmel.com/Images/Atmel-2586-AVR-8-bit-Microcontroller-ATtiny25-ATtiny45-ATtiny85_Datasheet.pdf|ATtiny85 Datasheet]]\\ | ||
| Line 93: | Line 95: | ||
| ---- | ---- | ||
| - | ~~socialite:icon facebook twitter googleplus reddit tumblr~~ | + | ==== License ==== |
| + | |||
| + | The PaperTiny was designed by **Wolfgang Spahn** 2017-18.\\ | ||
| + | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
| + | |||
| + | <html> | ||
| + | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
| + | </html> | ||
| ---- | ---- | ||