Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
arduino_clones:paperleonardo [2014/07/15 19:57] admin |
arduino_clones:paperleonardo [2021/01/30 14:04] (current) admin [License] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ---- | + | ==== Paper-Leonardo ===== |
| - | **Paper-Leonardo** | + | |
| - | ---- | + | |
| - | An other Arduino clone!\\ | + | {{ :arduino_clones:paper-duino-pi_wspahn_01.jpg?300 |}} |
| - | {{ :arduino_clones:paper-duino-pi_wspahn_01.jpg?400 |}}\\ | + | |
| - | The Paper-Leonardo is the only Paperduino Clone with USB on Board. But unfortunaltely cause its chip is an Atmega32U4 and that is only as SMD part availible one has to solder SMD.\\ | + | The Paper-Leonardo is the only Paperduino Clone with USB on Board and extra ISP pins. But unfortunaltely cause the board is based on an Atmega32U4 chip and is only availible in SMD one has to solder SMD.\\ |
| - | {{ :arduino_clones:paper-duino-pi_smd_wspahn_06.jpg?400 |}}\\ | + | {{ :arduino_clones:paper-duino-pi_smd_wspahn_06.jpg?400 |}} |
| - | Here is a manual for [[about:manual|SMD soldering]]\\. | + | |
| + | Here is a manual for [[about:smd-soldering|SMD soldering]]. | ||
| + | |||
| + | Front: | ||
| + | |||
| + | {{:arduino_clones:paper-duino-pi_wspahn_02.jpg?200|}} | ||
| + | |||
| + | Back: | ||
| + | |||
| + | {{:arduino_clones:paper-duino-pi_wspahn_03.jpg?200|}} | ||
| - | Front:\\ | ||
| - | {{:arduino_clones:paper-duino-pi_wspahn_02.jpg?100|}}\\ | ||
| - | Back:\\ | ||
| - | {{:arduino_clones:paper-duino-pi_wspahn_03.jpg?100|}}\\ | ||
| ---- | ---- | ||
| - | **Paper-PCBs** | + | ==== Paper-PCBs ==== |
| + | {{:arduino_clones:paper-leonardo_10.jpg?300|}}\\ | ||
| + | {{:arduino_clones:paper-leonardo_10.xcf.zip|Paper-leonardo_v10}} | ||
| ---- | ---- | ||
| - | **Schematic** | + | ==== Schematic ==== |
| + | {{:arduino_clones:paper-leonardo_schematic.jpg?500|}} | ||
| ---- | ---- | ||
| - | **Components** | + | ==== Parts ==== |
| * Atmega32U4 | * Atmega32U4 | ||
| * 4 lowcurrent LEDs | * 4 lowcurrent LEDs | ||
| Line 29: | Line 35: | ||
| * crystal 16MHz | * crystal 16MHz | ||
| * 2 elkos 100µF | * 2 elkos 100µF | ||
| - | * 4 capacitors 100nF | + | * 1 elko 10µF |
| + | * 5 capacitors 100nF | ||
| + | * 1 capacitor 1µF | ||
| * 2 capacitors 22pF | * 2 capacitors 22pF | ||
| + | * Z-Diode 3.6V | ||
| * diode 1N4007 | * diode 1N4007 | ||
| - | * resistors: 4x 2kOhm, 2x 1kOhm, 1x 10kOhm | + | * resistors: 4x 2.2kOhm, 2x 1kOhm, 2x 10kOhm, 2x 22Ohm |
| + | * poly fuse 500mA | ||
| + | * coil 10µH | ||
| * reset button | * reset button | ||
| * headers | * headers | ||
| Line 39: | Line 50: | ||
| ---- | ---- | ||
| + | ==== License ==== | ||
| + | The Paper-Leonardo and this page was designed by **Wolfgang Spahn** 2013.\\ | ||
| + | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
| + | |||
| + | <html> | ||
| + | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
| + | </html> | ||
| + | |||
| + | ---- | ||