Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
arduino_clones:papercocomake7 [2018/05/11 18:23]
admin [Links & Knowledge]
arduino_clones:papercocomake7 [2020/06/11 22:13] (current)
Line 1: Line 1:
-===== PaperCocoMake7 ​=====+===== Paper CocoMake7 ​=====
  
-The PaperCocoMake7 in an Arduino board based on Paper PCB and an ATtiny85 chip. It is the paper version of the [[https://​cocomake7.github.io/#​|CocoMake7]]. ​Like the CocoMake7 one can upload code over the sound card of your PC.\\ +The PaperCocoMake7 in an Arduino board based on Paper PCB and an ATtiny85 chip. It is the paper version of the [[https://​cocomake7.github.io/#​|CocoMake7]].
-An older version of the board the PaperCocoMake1 one can finde here.\\+
 Thanks to Marc, Yashas, Shreyasi and Budi from [[https://​cocomake7.github.io/#​|Cocomake7]].\\ Thanks to Marc, Yashas, Shreyasi and Budi from [[https://​cocomake7.github.io/#​|Cocomake7]].\\
 For code and the Arduino IDE mod please follow the [[https://​cocomake7.github.io/#​|CocoMake7 webside]].\\ For code and the Arduino IDE mod please follow the [[https://​cocomake7.github.io/#​|CocoMake7 webside]].\\
 +Here you find an other ATiny board the [[arduino_clones:​papertiny|PaperTiny]].\\
  
-{{:​arduino_clones:​papercocomake7.jpg|}}\\+**Paper CocoMake7**\\ 
 +{{:​arduino_clones:​papercocomake7.jpg?400|}}\\ 
 + 
 +**Paper CocoMake**\\ 
 +{{:​arduino_clones:​papercocomake1.jpg?​400|}}\\
 ---- ----
 ==== Paper PCB ==== ==== Paper PCB ====
 +
 +**Paper CocoMake7** with audio out and no power on board:\\
 {{:​arduino_clones:​papercocomake7_03.jpg?​200|}}\\ {{:​arduino_clones:​papercocomake7_03.jpg?​200|}}\\
-{{ :​arduino_clones:​papercocomake7_03.zip |}}+{{ :​arduino_clones:​papercocomake7_03.zip |}}\\ 
 + 
 +**Paper CocoMake** with power on board no audio out:\\ 
 +{{:​arduino_clones:​papercocomake1_10.jpg?​200|}}\\ 
 +{{ :​arduino_clones:​papercocomake1_10.zip |}}\\ 
 + 
 +---- 
 +==== Schematic ==== 
 +It's the same schematic as the one from [[https://​cocomake7.github.io/#​]],​ I just used 2k as the LED resistors and added a power supply.\\ 
 +{{:​arduino_clones:​mrbaladuinoone_schematic.png?​400|}}\\
  
 ---- ----
 ==== Parts ==== ==== Parts ====
   * **Resistors:​**   * **Resistors:​**
-  * 2x 220 Ohm+  * 2x 2 kOhm
   * 1x 1.5 kOhm   * 1x 1.5 kOhm
-  * 1x 47 kOhm+  * 1x 47 kOhm(1)
   * 2x 68 Ohm   * 2x 68 Ohm
   * **Capacitors:​**   * **Capacitors:​**
-  * 1x 100 nF+  * 2x 100 nF 
 +  * 1x 10µF(1) 
 +  * 1x 100µF(2)
   * **Diodes:**   * **Diodes:**
   * 2x Z-Diode 3,3V   * 2x Z-Diode 3,3V
   * **Semiconductors**   * **Semiconductors**
   * 2x Standart LED   * 2x Standart LED
 +  * 1x 7805(2)
   * **Mechanical:​**   * **Mechanical:​**
   * 1x IC socket, 8pins   * 1x IC socket, 8pins
-  * 1x Pin-Strip male 1x2+  * 1x Pin-Strip male 1x2(2)
   * 2x Pin-Strip female 1x4   * 2x Pin-Strip female 1x4
-  * jack socket+  * jack socket(1)
  
 +(1) Paper CocoMake7\\
 +(2) Paper CocoMake\\
  
 ---- ----
 +==== License ====
 +
 +The Paper CocoMake7 was designed by **Wolfgang Spahn** 2017-18.\\
 +It is licensed under a [[http://​creativecommons.org/​licenses/​by-nc-sa/​4.0/"​|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]].
  
-~~socialite:icon facebook twitter googleplus reddit tumblr~~+<​html>​ 
 +<a rel="​license"​ href="​http://​creativecommons.org/​licenses/​by-nc-sa/​4.0/"><​img alt="​Creative Commons License"​ style="​border-width:​0"​ src="​https://​i.creativecommons.org/​l/​by-nc-sa/​4.0/​88x31.png"​ /></​a>​  
 +</​html>​
  
 ---- ----