Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
arduino_clones:paper-duino-mini [2016/06/07 15:06] admin [Parts] |
arduino_clones:paper-duino-mini [2020/06/11 22:13] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
===== Paper-Duino-Mini ===== | ===== Paper-Duino-Mini ===== | ||
+ | {{:arduino_clones:paper-duino-mini.jpg?400|}}\\ | ||
The Paper-Duino-Mini is the super reduced version of the Paperduino-Uno. It's perfect to build it in fabric for wearables or to build into (inter)active pictures.\\ | The Paper-Duino-Mini is the super reduced version of the Paperduino-Uno. It's perfect to build it in fabric for wearables or to build into (inter)active pictures.\\ | ||
- | It comes with a small power regulator and an LED on pin 13 - but that's all.And one needs an additional programming adapter for loading up the scetches.\\ | + | It comes with a small power regulator and an LED on pin 13 - but that's all.\\ |
+ | Front:\\ | ||
+ | {{:arduino_clones:paper-duino-mini_front.jpg?200|}}\\ | ||
+ | Back:\\ | ||
+ | {{:arduino_clones:paper-duino-mini_back.jpg?200|}}\\ | ||
+ | Beside the USB to Serial adapter one needs an additional programming adapter for loading up the sketches.\\ | ||
+ | Front:\\ | ||
+ | {{:arduino_clones:paper-duino-mini-adapter_front.jpg?200|}}\\ | ||
+ | Back:\\ | ||
+ | {{:arduino_clones:paper-duino-mini-adapter_back.jpg?200|}}\\ | ||
+ | All about uploading a sketch without a Serial-to USB adapter one can find here: [[arduino_clones:serial_adapter|The Arduino as a Serial Adapter]]\\ | ||
+ | And all about the bootloader is here:[[avr_bootloader:bootloader|Burning the Bootloader]]\\ | ||
+ | {{:arduino_clones:paper-duino-mini_adapter.jpg?400|}} | ||
---- | ---- | ||
==== Paper-PCB ==== | ==== Paper-PCB ==== | ||
+ | {{:arduino_clones:paper-duino-mini_04.png?200|}}\\ | ||
+ | {{:arduino_clones:paper-duino-mini_04.ai.zip|}}\\ | ||
---- | ---- | ||
==== Parts ==== | ==== Parts ==== | ||
+ | * Atmega328 | ||
+ | * 1 low current LED | ||
+ | * voltage converter 78M05 | ||
+ | * crystal 16MHz | ||
+ | * 1 elkos 100µF | ||
+ | * 2 capacitors 100nF | ||
+ | * 2 capacitors 22pF | ||
+ | * diode 1N4007 | ||
+ | * resistors: 1x 2kOhm, 2x 470Ohm, 1x 10kOhm | ||
+ | * reset button | ||
+ | * pin headers & sockets | ||
+ | * battery clip | ||
---- | ---- | ||
- | ~~socialite:icon facebook twitter googleplus reddit~~ | + | ==== Paper-Duino-Mini ==== |
+ | |||
+ | The Experimental VGA Processor was designed by **Wolfgang Spahn** 2016.\\ | ||
+ | It is licensed under a [[http://creativecommons.org/licenses/by-nc-sa/4.0/"|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. | ||
+ | |||
+ | <html> | ||
+ | <a rel="license" href="http://creativecommons.org/licenses/by-nc-sa/4.0/"><img alt="Creative Commons License" style="border-width:0" src="https://i.creativecommons.org/l/by-nc-sa/4.0/88x31.png" /></a> | ||
+ | </html> | ||
---- | ---- |