Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
arduino_clones:fabric-duino [2016/06/13 19:29]
admin
arduino_clones:fabric-duino [2020/06/11 22:13] (current)
Line 1: Line 1:
 ===== Fabric-Duino ===== ===== Fabric-Duino =====
-{{:​arduino_clones:​fabric-duino_011229.jpg?​400|}}\\ +{{ :​arduino_clones:​fabric-duino_011229.jpg?​400 |}}\\ 
-The Fabric-Duino is basically a version of the [[arduino_clones:​paper-duino-mini|Paper-Duino-Mini]]One use fabric ​instead of the paper. And as connector one make small wire eye.\\+The Fabric-Duino is an Arduino clone for fabric. And for connectors one can make small wire eye.\\ 
 +{{ :arduino_clones:​duino-shirt.jpg?​400 ​|}}\\ 
 +All Paper-Duino ​version will works as well, but the smaller version is much handier.\\ 
 + 
 +---- 
 +==== Paper PCB ==== 
 +{{:​arduino_clones:​fabric-duino_02.jpg?​300|}}\\ 
 +{{ :​arduino_clones:​fabric-duino_02.zip |}}\\ 
 + 
 +---- 
 +==== Workaround ====
 01. Iron the printout on fabric:\\ 01. Iron the printout on fabric:\\
 {{:​arduino_clones:​fabric-duino_01_174501.jpg?​200|}}\\ {{:​arduino_clones:​fabric-duino_01_174501.jpg?​200|}}\\
-02. Cut a Copper-Stripe-Board ​in the right sice:\\+02. Cut a Copper-Stripe-Board ​to the right sice:\\
 {{:​arduino_clones:​fabric-duino_02_181905.jpg?​200|}}\\ {{:​arduino_clones:​fabric-duino_02_181905.jpg?​200|}}\\
-03. Solder all parts in:\\+03. Solder all parts:\\
 {{:​arduino_clones:​fabric-duino_03_194424.jpg?​200|}}\\ {{:​arduino_clones:​fabric-duino_03_194424.jpg?​200|}}\\
 The back should looks like that:\\ The back should looks like that:\\
 {{:​arduino_clones:​fabric-duino_03_back_194449.jpg?​200|}}\\ {{:​arduino_clones:​fabric-duino_03_back_194449.jpg?​200|}}\\
 +For wireing parts like LEDs and switches one need some Conductive Thread and a needle.\\
  
 ---- ----
-For uploading a scetch one need the Adappter-Board and a Serial to USB board.\\ +==== Software ==== 
-{{:arduino_clones:​fabric-duino_upload_194346.jpg?400|}}\\ +One should first burn the bootloader on the chip: [[avr_bootloader:​bootloader|Burning the Bootloader]]\\ 
-~~socialite:icon facebook twitter googleplus reddit~~+For uploading a scetch one need a Serial to USB board or: [[arduino_clones:​serial_adapter|The Arduino as a Serial Adapter]]\\ 
 + 
 +---- 
 +==== Parts ==== 
 +  * Atmega328 
 +  * 1 LED 
 +  * voltage converter 7805 
 +  * crystal 16MHz 
 +  * 1 elkos 100µF 
 +  * 4 capacitors 100nF 
 +  * 2 capacitors 22pF 
 +  * diode 1N4007 
 +  * resistors1x 330Ohm, 2x 470Ohm, 1x 10kOhm 
 +  * push button 
 +  * pin headers & sockets 
 +  * battery clip 
 + 
 +---- 
 +==== License ==== 
 + 
 +The Fabric-Duino was designed by **Wolfgang Spahn** 2017.\\ 
 +It is licensed under a [[http://​creativecommons.org/​licenses/​by-nc-sa/​4.0/"​|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. 
 + 
 +<​html>​ 
 +<a rel="​license"​ href="​http://​creativecommons.org/​licenses/​by-nc-sa/​4.0/"><​img alt="​Creative Commons License"​ style="​border-width:​0"​ src="​https://​i.creativecommons.org/​l/​by-nc-sa/​4.0/​88x31.png"​ /></​a>​  
 +</​html>​
  
 ---- ----