Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
analog_computer:confetti101_gyrator [2019/07/01 20:43]
admin [Confetti101 Gyrator]
analog_computer:confetti101_gyrator [2020/06/11 22:13] (current)
Line 4: Line 4:
 With the jumper set one can connect the output to the common ground, if no jumper is used one can use the output connector instead.\\ With the jumper set one can connect the output to the common ground, if no jumper is used one can use the output connector instead.\\
 Together with the [[analog_computer:​confetti102_chua_diode|Confetti102 Chua Diode]] one can build a [[https://​en.wikipedia.org/​wiki/​Chua%27s_circuit|Chua'​s Oscillator]].\\ Together with the [[analog_computer:​confetti102_chua_diode|Confetti102 Chua Diode]] one can build a [[https://​en.wikipedia.org/​wiki/​Chua%27s_circuit|Chua'​s Oscillator]].\\
 +
 +{{:​analog_computer:​chua_s_circuit_pure_134355.jpg?​600|}}\\
 +[[https://​dernulleffekt.de/​doku.php?​id=analogcomputation:​01_chuascircuit#​analog_computation_01_-_chua_s_circuit|Analog Computing 01 - Chua's Circuit]]\\
 +
  
 ---- ----
 ==== Paper PCB ==== ==== Paper PCB ====
  
-{{:​analog_computer:​confetti101_gyrator_02.jpg?​400|}}\\ +{{:​analog_computer:​confetti101_gyrator_03_15mh.jpg?​400|}}\\ 
-{{ :​analog_computer:​confetti101_gyrator_02.zip |}}\\+{{ :​analog_computer:​confetti101_gyrator_03_15mh.zip |}}\\ 
 + 
 +---- 
 +==== Parts ==== 
 + 
 +To build this board one needs a copper stripe protoboard (1/6 of the 16x10cm board), a paper print out (1:1) and some copper wire for the bridges. 
 + 
 +  * **Resistors:​** 
 +  * 1x 100 Ohm 
 +  * 2x 1 kOhm 
 +  * **Capacitors:​** 
 +  * 1x 100nF 
 +  * **Semiconductors** 
 +  * 1x TL072 OpAmp 
 +  * **Mechanical:​** 
 +  * 1x IC socket, 8pins 
 +  * 1x 2 pin strip 
 +  * 1x 1 pin 
 +  * 3x 2 pin header, female  
 +  * 2x pin header, female 90° 1x3, 1x2 
 +  * 2x pin header, male 90° 1x3, 1x2 
 +  * 1x jumpers 
 +  * **Trimpotentiometer:​** 
 +  * 1x 5 kOhm 
 + 
 +---- 
 +==== License ==== 
 + 
 +The Confetti101 Gyrator was designed by **Wolfgang Spahn** 2015-20.\\ 
 +It is licensed under a [[http://​creativecommons.org/​licenses/​by-nc-sa/​4.0/"​|Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License]]. 
 + 
 +<​html>​ 
 +<a rel="​license"​ href="​http://​creativecommons.org/​licenses/​by-nc-sa/​4.0/"><​img alt="​Creative Commons License"​ style="​border-width:​0"​ src="​https://​i.creativecommons.org/​l/​by-nc-sa/​4.0/​88x31.png"​ /></​a>​  
 +</​html>​
  
 ---- ----